IBM0612404GT3B
IBM0612804GT3B
128Mb Double Data Rate Synchronous DRAM
Advance Rev 0.2
Truth Table 4: Current State Bank n - Command to Bank m (Different bank)
(Part 1 of 2)
Current State
Any
CS
H
RAS CAS
WE
X
Command
Deselect
Action
Notes
1-6
X
H
X
H
NOP/continue previous operation
NOP/continue previous operation
L
H
No Operation
1-6
Any Command Otherwise
Allowed to Bank m
Idle
X
X
X
X
1-6
L
L
L
L
L
L
L
L
L
L
L
L
H
H
L
H
L
H
H
L
Active
Read
Select and activate row
1-6
1-7
1-7
1-6
1-6
1-7
1-6
1-6
1-8
1-7
1-6
Row Activating,
Active, or
Precharging
Select column and start Read burst
Select column and start Write burst
L
Write
H
H
L
L
Precharge
Active
L
H
H
L
Select and activate row
Read
(Auto Precharge
Disabled)
H
L
Read
Select column and start new Read burst
H
H
L
Precharge
Active
L
H
H
L
Select and activate row
Write
(Auto Precharge
Disabled)
H
H
L
Read
Select column and start Read burst
Select column and start new Write burst
L
Write
H
L
Precharge
1. This table applies when CKE n-1 was high and CKE n is high (see Truth Table 2: Clock Enable (CKE) and after t
t
has
XSNR / XSRD
been met (if the previous state was self refresh).
2. This table describes alternate bank operation, except where noted, i.e., the current state is for bank n and the commands shown
are those allowed to be issued to bank m (assuming that bank m is in such a state that the given command is allowable). Excep-
tions are covered in the notes below.
3. Current state definitions:
Idle:
Row Active:
The bank has been precharged, and t has been met.
RP
A row in the bank has been activated, and t
accesses are in progress.
has been met. No data bursts/accesses and no register
RCD
Read:
Write:
A Read burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated.
A Write burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated.
Read with Auto Precharge Enabled: See note 10.
Write with Auto Precharge Enabled: See note 10.
4. Auto Refresh and Mode Register Set commands may only be issued when all banks are idle.
5. A Burst Terminate command cannot be issued to another bank; it applies to the bank represented by the current state only.
6. All states and sequences not shown are illegal or reserved.
7. Reads or Writes listed in the Command/Action column include Reads or Writes with Auto Precharge enabled and Reads or Writes
with Auto Precharge disabled.
8. Requires appropriate DM masking.
9. A Write command may be applied after the completion of data output.
10. The Read with Auto Precharge enabled or Write with Auto Precharge enabled states can each be broken into two parts: the
access period and the precharge period. For Read with Auto Precharge, the precharge period is defined as if the same burst was
executed with Auto Precharge disabled and then followed with the earliest possible Precharge command that still accesses all of
the data in the burst. For Write with Auto Precharge, the precharge period begins when t
ends, with t
measured as if Auto
WR
WR
Precharge was disabled. The access period starts with registration of the command and ends where the precharge period (or t
begins. During the precharge period of the Read with Auto Precharge Enabled or Write with Auto Precharge Enabled states,
)
RP
Active, Precharge, Read, and Write commands to the other bank may be applied; during the access period, only Active and Pre-
charge commands to the other bank may be applied. In either case, all other related limitations apply (e.g. contention between
Read data and Write data must be avoided).
©IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
06K0566.F39350
5/00
Page 48 of 79
IBM [ IBM ]
