HMC1060LP3E
v00.1211
QUAD LOW NOISE HIGH PSRR
LINEAR VOLTAGE REGULATOR
Electrical Specifications
Parameter
output Voltage on All outputs
default output Voltage Vr1, Vr2, Vr3
default output Voltage Vr4
output Voltage tolerance
[1]
input Voltage range (default)
input Voltage range
[2]
output Current Vr1
[3]
output Current Vr2, Vr3
[3]
output Current Vr4
[3]
total output Current
output noise Voltage density
10 Hz
100 Hz
1 kHz
10 kHz
100 kHz
integrated output noise 100 Hz to 100 kHz
Load regulation, Vr4
Vr1 PSrr
1 kHz
10 kHz
100 KHz
1 MHz
10 MHz
Current Consumption (i
gnd
)
Power down Current
Start-Up transient time
Ven = Vdd = 5.6 V;
Maximum Load Current
Ven = Low; Vrx outputs are floating (high
- impedance) in Power-down Mode
0 to 90% of final voltage;
en connected to Vdd
0 to 90% of final output voltage
Cref = 4.7 µF; Cload = 10 µF; Vdd = 5.6
Ven transition from 0 to Vdd
2
0
no loads
All outputs Loaded
150
1.6
0 to 300 mA
t
A
= -40 °C to +85 °C
t
A
= -40 °C to +85 °C
t
A
= -40 °C to +85 °C
t
A
= -40 °C to +85 °C
2200
120
7
3
3
1.5
0.007
80
80
72
60
52
2.1
1
50
2
default Configuration shown in
PtAt Mode disabled
PtAt Mode enabled
5.3
3.35
Max (Vrx) +
0.3 V
Conditions
Min
1.8
3.24
4.9
typ
Max
5.2
Units
V
V
V
%
%
V
V
mA
mA
mA
mA
3.3
5.0
3.36
5.1
2
3
5.6
5.6
100
50
300
500
nV/√Hz
µVrms
% / mA
dB
mA
µA
ms
en turn-on delay
enable input en High Level
enable input en Low Level
thermal Protection threshold Junction
temperature
Maximum dissipated Power
30
Vdd + 0.3
0.8
ms
V
V
°C
w
[1] when using external resistors to configure the HMC1060LP3e outputs to non-default levels, the temperature coefficient of external resistors
may increase the output voltage tolerance. note that internal resistors have a temperature coefficient of +270 ppm/°C.
[2] Minimum input voltage (Vdd) is defined by maximum desired output voltage. As an example minimum input voltage (Vdd) of 4.3 V is required
to set the HMC1060LP3e outputs as follows Vr1 = Vr2 = Vr3 = 3.3 V, Vr4 = 4 V.
[3] the outputs will withstand short-circuit conditions for a duration of less than 10 seconds.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
Power Conditioning - SMt
2
t
A
= +25 °C, Vdd = 5.6 V, Unless otherwise Specified, PtAt Mode is disabled, measured at maximum load conditions
in default configuration as shown in
HITTITE [ HITTITE MICROWAVE CORPORATION ]
