欢迎访问ic37.com |
会员登录 免费注册
发布采购

HMF51232J4V-70 参数 Datasheet PDF下载

HMF51232J4V-70图片预览
型号: HMF51232J4V-70
PDF下载: 下载PDF文件 查看货源
内容描述: FLASH- ROM模块2MByte ( 512K ×32位) - 68引脚JLCC [FLASH-ROM MODULE 2MByte (512K x32-Bit) - 68-Pin JLCC]
分类和应用:
文件页数/大小: 11 页 / 419 K
品牌: HANBIT [ HANBIT ELECTRONICS CO.,LTD ]
 浏览型号HMF51232J4V-70的Datasheet PDF文件第1页浏览型号HMF51232J4V-70的Datasheet PDF文件第2页浏览型号HMF51232J4V-70的Datasheet PDF文件第4页浏览型号HMF51232J4V-70的Datasheet PDF文件第5页浏览型号HMF51232J4V-70的Datasheet PDF文件第6页浏览型号HMF51232J4V-70的Datasheet PDF文件第7页浏览型号HMF51232J4V-70的Datasheet PDF文件第8页浏览型号HMF51232J4V-70的Datasheet PDF文件第9页  
HANBit  
HMF51232J4V  
Sector Address,  
A6=L,A1=H,A0=L  
AIN  
Sector Unprotect  
L
H
X
L
DIN,DOUT  
DIN  
Temporary Sector Unprotect  
Note : X means don't care  
X
X
ABSOLUTE MAXIMUM RATINGS  
PARAMETER  
SYMBOL  
RATING  
Voltage with respect to ground all other pins  
Voltage with respect to ground Vcc  
Storage Temperature  
VIN,OUT  
VCC  
-0.5V to Vcc +0.5V  
-0.5V to +4.0V  
o o  
-65 C to +150 C  
TSTG  
o o  
-55 C to +125 C  
Operating Temperature  
TA  
w Stresses greater than those listed under " Absolute Maximum Ratings" may cause permanent damage to the device.  
This is a stress rating only and functional operation of the device at these or any other conditions above those indicated  
in the operating section of this specification is not implied. Exposure to absolute maximum rating conditions for extended  
periods may affect reliability.  
RECOMMENDED DC OPERATING CONDITIONS  
SYMBOL  
MIN  
TYP.  
MAX  
PARAMETER  
Vcc for regulated voltage range  
Vcc for full voltage range  
Ground  
VCC  
Vcc  
VSS  
3.0V  
2.7V  
0
3.6V  
3.6V  
0
0
o
o
DC AND OPERATING CHARACTERISTICS (0 C £ T £ 70 C ; Vcc = 5V ± 0.5V )  
A
TEST CONDITIONS  
SYMBOL  
MIN  
MAX  
UNITS  
PARAMETER  
Input Leakage Current  
Vcc=Vcc max, VIN= GND to Vcc  
Vcc=Vcc max, Vout= GND to Vcc  
IOH = -2.0mA, Vcc = Vcc min  
IOL = 4.0mA, Vcc =Vcc min  
/CE = VIL, /OE=VIH, f=5mHz  
IL1  
IL0  
±1.0  
±1.0  
mA  
mA  
V
Output Leakage Current  
Output High Voltage  
Output Low Voltage  
Vcc Active Current for Read(1)  
Vcc Active Current for Program  
or Erase(2)  
VOH  
VOL  
ICC1  
0.85Vcc  
0.45  
12  
V
mA  
/CE = VIL, /OE=VIH  
ICC2  
30  
mA  
Vcc Standby Current  
Vcc Reset Current  
/CE=Vcc±0.3V  
ICC3  
ICC4  
5
5
mA  
mA  
V
Low Vcc Lock-Out Voltage  
Notes:  
VLKO  
2.3  
2.5  
1. The Icc current listed is typically less than than 2mA/MHz, with /OE at VIH. Typical Vcc is 3.0V  
2. Icc active while embedded algorithm (program or erase) is in progress  
3. Maximum Icc current specifications are tested with Vcc=Vcc max  
3
URL: www.hbe.co.kr  
REV.02(August,2002)  
HANBit Electronics Co., Ltd.