MBM29F800TA-55/-70/-90/MBM29F800BA-55/-70/-90
RY/BY
Ready/Busy
The MBM29F800TA/BA provides a RY/BY open-drain output pin as a way to indicate to the host system that the
Embedded Algorithms are either in progress or has been completed. If the output is low, the device is busy with
either a program or erase operation. If the output is high, the device is ready to accept any read/write or erase
operation. When the RY/BY pin is low, the device will not accept any additional program or erase commands. If
the MBM29F800TA/BA is placed in an Erase Suspend mode, the RY/BY output will be high. Also, since this is
an open drain output, many RY/BY pins can be tied together in parallel with a pull up resistor to VCC.
During programming, the RY/BY pin is driven low after the rising edge of the fourth WE pulse. During an erase
operation, the RY/BY pin is driven low after the rising edge of the sixth WE pulse. The RY/BY pin will indicate a
busy condition during the RESET pulse. Refer to Figure 11 and 12 for a detailed timing diagram.
Sincethisisanopen-drainoutput, severalRY/BYpinscanbetiedtogetherinparallelwithapull-upresistortoVCC.
RESET
Hardware Reset
The MBM29F800TA/BA device may be reset by driving the RESET pin to VIL. The RESET pin has a pulse
requirement and has to be kept low (VIL) for at least 500 ns in order to properly reset the internal state machine.
Any operation in the process of being executed will be terminated and the internal state machine will be reset
to the read mode 20 µs after the RESET pin is driven low. Furthermore, once the RESET pin goes high, the
device requires time of tRH before it will allow read access. When the RESET pin is low, the device will be in the
standby mode for the duration of the pulse and all the data output pins will be tri-stated. If a hardware reset
occurs during a program or erase operation, the data at that particular location will be corrupted. Please note
thattheRY/BYoutputsignalshouldbeignoredduringtheRESETpulse. RefertoFigure12forthetimingdiagram.
Refer to Temporary Sector Unprotection for additional functionality.
If hardware reset occurs during Embedded Erase Algorithm, there is a possibility that the erasing sector(s)
cannot be used.
Byte/Word Configuration
The BYTE pin selects the byte (8-bit) mode or word (16-bit) mode for the MBM29F800TA/BA device. When this
pin is driven high, the device operates in the word (16-bit) mode. The data is read and programmed at DQ0 to
DQ15. When this pin is driven low, the device operates in byte (8-bit) mode. Under this mode, the DQ15/A-1 pin
becomes the lowest address bit and DQ8 to DQ14 bits are tri-stated. However, the command bus cycle is always
an 8-bit operation and hence commands are written at DQ0 to DQ7 and the DQ8 to DQ15 bits are ignored. Refer
to Figures 13, 14 and 15 for the timing diagram.
Data Protection
The MBM29F800TA/BA are designed to offer protection against accidental erasure or programming caused by
spurious system level signals that may exist during power transitions. During power up the device automatically
resets the internal state machine in the read mode. Also, with its control register architecture, alteration of the
memory contents only occurs after successful completion of specific multi-bus cycle command sequences.
The device also incorporate several features to prevent inadvertent write cycles resulting form VCC power-up and
power-down transitions or system noise.
Low VCC Write Inhibit
To avoid initiation of a write cycle during VCC power-up and power-down, a write cycle is locked out for VCC less
than 3.2 V (typically 3.7 V). If VCC < VLKO, the command register is disabled and all internal program/erase circuits
are disabled. Under this condition the device will reset to the read mode. Subsequent writes will be ignored until
the VCC level is greater than VLKO. It is the users responsibility to ensure that the control pins are logically correct
to prevent unintentional writes when VCC is above 3.2 V.
If Embedded Erase Algorithm is interrupted, there is possibility that the erasing sector(s) cannot be used.
21
FUJITSU [ FUJITSU ]
