欢迎访问ic37.com |
会员登录 免费注册
发布采购

FT2232HQ-4000 参数 Datasheet PDF下载

FT2232HQ-4000图片预览
型号: FT2232HQ-4000
PDF下载: 下载PDF文件 查看货源
内容描述: 双高速USB TO多用途UART / FIFO IC [DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC]
分类和应用: 先进先出芯片
文件页数/大小: 63 页 / 1469 K
品牌: FTDI [ FUTURE TECHNOLOGY DEVICES INTERNATIONAL LTD. ]
 浏览型号FT2232HQ-4000的Datasheet PDF文件第14页浏览型号FT2232HQ-4000的Datasheet PDF文件第15页浏览型号FT2232HQ-4000的Datasheet PDF文件第16页浏览型号FT2232HQ-4000的Datasheet PDF文件第17页浏览型号FT2232HQ-4000的Datasheet PDF文件第19页浏览型号FT2232HQ-4000的Datasheet PDF文件第20页浏览型号FT2232HQ-4000的Datasheet PDF文件第21页浏览型号FT2232HQ-4000的Datasheet PDF文件第22页  
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Datasheet Version 2.09
Clearance No.: FTDI#77
3.4.8 FT2232H Pins Configured as a Host Bus Emulation Interface
The FT2232H can be used to combine channel A and channel B to be configured as a host bus emulation
interface mode which emulates a standard 8048 or 8051 MCU host.
When configured in this mode, the pins used and the descriptions of the signals are shown in
Pin No.
24,23,22,21,
19,18,17,16
34,33,32,30,
29,28,27,26
Name
ADBUS[7:0]
Type
Fast Serial Interface Configuration Description
I/O
Multiplexed bidirectional Address/Data bus AD7 to AD0
A[15:8]
OUTPUT
Extended Address A15 to A8
38
CS#
OUTPUT
Active low chip select device during Read or Write.
39
ALE
OUTPUT
Positive pulse to latch the address
40
RD#
OUTPUT
Active low read output.
41
WR#
OUTPUT
Active low write output. (Data is setup before WR# goes
low, and is held after WR# goes high)
43
IORDY
INPUT
Extends the time taken to perform a Read or Write
operation if driven low. Pull up to VCORE if not being
used.
Master clock. Outputs the clock signal being used by the
configured interface.
MPSSE mode instructions to set / clear or read the high
byte of data can be used with this pin. Please refer to
Application Note
AN_108
for operation of these
instructions.
MPSSE mode instructions to set / clear or read the high
byte of data can be used with this pin. In addition this
pin has instructions which will make the controller wait
until it is high, or wait until it is low. This can be used to
connect to an IRQ pin of a peripheral chip. The FT2232H
will wait for the interrupt, and then read the device, and
pass the answer back to the host PC. I/O1 must be held
in input mode if this option is used. Please refer to
Application Note
AN_108
for operation of these
instructions.
44
CLKOUT
OUTPUT
I/O
45
I/O0
I/O
46
I/O1
Table 3.11 Channel A and Channel B Host Bus Emulation Interface Configured Pin Descriptions
For a functional description of this mode, please refer to section 4.7 MCU Host Bus Emulation Mode
Copyright © 2010 Future Technology Devices International Limited
18