欢迎访问ic37.com |
会员登录 免费注册
发布采购

FT2232HQ-4000 参数 Datasheet PDF下载

FT2232HQ-4000图片预览
型号: FT2232HQ-4000
PDF下载: 下载PDF文件 查看货源
内容描述: 双高速USB TO多用途UART / FIFO IC [DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC]
分类和应用: 先进先出芯片
文件页数/大小: 63 页 / 1469 K
品牌: FTDI [ FUTURE TECHNOLOGY DEVICES INTERNATIONAL LTD. ]
 浏览型号FT2232HQ-4000的Datasheet PDF文件第10页浏览型号FT2232HQ-4000的Datasheet PDF文件第11页浏览型号FT2232HQ-4000的Datasheet PDF文件第12页浏览型号FT2232HQ-4000的Datasheet PDF文件第13页浏览型号FT2232HQ-4000的Datasheet PDF文件第15页浏览型号FT2232HQ-4000的Datasheet PDF文件第16页浏览型号FT2232HQ-4000的Datasheet PDF文件第17页浏览型号FT2232HQ-4000的Datasheet PDF文件第18页  
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Datasheet Version 2.09
Clearance No.: FTDI#77
3.4.4 FT2232H pins used in a Synchronous or Asynchronous Bit-Bang
Interface
The FT2232H channel A or channel B can be configured as a synchronous or asynchronous bit-bang
interface. Bit-bang mode is a special FTDI FT2232H device mode that changes the 8 IO lines on either (or
both) channels into an 8 bit bi-directional data bus. There are two types of bit-bang modes: synchronous
and asynchronous.
When configured in any bit-bang mode, the pins used and the descriptions of the signals are shown in
Channel A
Pin No.
24,23,22,21
,
19,18,17,16
Channel B
Pin No.
Name
Type
Configuration Description
46,45,44,43,
41,40,39,38
Channel A =
ADBUS[7:0]
Channel B =
BDBUS[7:0]
I/O
D7 to D0 bidirectional Bit-Bang parallel I/O
data pins
27
52
WRSTB#
OUTPUT
Write strobe, active low output indicates
when new data has been written to the I/O
pins from the Host PC (via the USB
interface).
Read strobe, this output rising edge
indicates when data has been read from the
parallel I/O pins and sent to the Host PC
(via the USB interface).
The Send Immediate / WakeUp signal
combines two functions on a single pin. If
USB is in suspend mode (PWREN# = 1) and
remote wakeup is enabled in the EEPROM ,
strobing this pin low will cause the device to
request a resume on the USB Bus.
Normally, this can be used to wake up the
Host PC.
During normal operation (PWREN# = 0), if
this pin is strobed low any data in the device
TX buffer will be sent out over USB on the
next Bulk-IN request from the drivers
regardless of the pending packet size. This
can be used to optimize USB transfer speed
for some applications. Tie this pin to VCCIO
if not used. (Also see note 1, 2, 3 in section
28
53
RDSTB#
OUTPUT
30
55
SIWU
INPUT
Table 3.7 Channel A and Channel B Synchronous or Asynchronous Bit-Bang Configured Pin Descriptions
For a functional description of this mode, please refer to section 4.10 Synchronous and Asynchronous Bit-
Copyright © 2010 Future Technology Devices International Limited
14