欢迎访问ic37.com |
会员登录 免费注册
发布采购

ES25P80-75IC2Y 参数 Datasheet PDF下载

ES25P80-75IC2Y图片预览
型号: ES25P80-75IC2Y
PDF下载: 下载PDF文件 查看货源
内容描述: 8Mbit的CMOS 3.0伏闪存为75Mhz SPI总线接口 [8Mbit CMOS 3.0 Volt Flash Memory with 75Mhz SPI Bus Interface]
分类和应用: 闪存
文件页数/大小: 35 页 / 436 K
品牌: EXCELSEMI [ EXCEL SEMICONDUCTOR INC. ]
 浏览型号ES25P80-75IC2Y的Datasheet PDF文件第12页浏览型号ES25P80-75IC2Y的Datasheet PDF文件第13页浏览型号ES25P80-75IC2Y的Datasheet PDF文件第14页浏览型号ES25P80-75IC2Y的Datasheet PDF文件第15页浏览型号ES25P80-75IC2Y的Datasheet PDF文件第17页浏览型号ES25P80-75IC2Y的Datasheet PDF文件第18页浏览型号ES25P80-75IC2Y的Datasheet PDF文件第19页浏览型号ES25P80-75IC2Y的Datasheet PDF文件第20页  
E S I  
E S I  
ADVANCED INFORMATION  
Excel Semiconductor inc.  
CS#  
0
0
1
2
3
4
5
6
7
8
9
10  
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47  
SCK  
SI  
Dummy Byte  
24-Bit Address  
Instruction  
3
0
7
6
5
4
3
2
1
0
23  
1
22 21  
2
1
0
0
0
1
0
1
MSB  
Data Out 2  
7
Data Out 1  
High Impedance  
7
4
3
2
1
0
6
5
SO  
MSB  
Figure 10. Read Data Bytes at Higher Speed (FAST_READ) Instruction Sequence  
This is followed by the 24-bit device identification,  
stored in the memory, being shifted out on Serial  
Read Identification (RDID)  
Data Output (SO), with each bit being shifted out  
during the falling edge of Serial Clock (SCK).  
The Read Identification (RDID) instruction allows the  
8-bit manufacturer identification to be read, followed  
by two bytes of the device identification.  
The instruction sequence is shown in Figure 11.  
The manufacturer identification byte is assigned by  
JEDEC, and has a value of 4Ah for ESI products.  
The device identification is assigned by the device  
manufacturer, and indicates the memory type in the  
first byte (20h), and the memory capacity of the  
device in the second byte (14h).  
Driving CS# high after the Device Identification has  
been read at least once terminates the READ_ID  
instruction. The Read Identification (RDID) instruc-  
tion can also be terminated by driving CS# High at  
any time during data output. When Chip Select  
(CS#) is driven High, the device is put in the Stand-  
by Power mode. Once in the Stand-by Power  
mode, the device waits to be selected, so that it can  
receive, decode and execute instructions  
Any Read Identification (RDID) instruction executed  
while an Erase, Program, or Write Status Register  
cycle is in progress is not decoded, and has no  
effect on the cycle that is in progress.  
Manufacturer  
Identification  
Device Identification  
The device is first selected by driving Chip Select  
(CS#) Low. Then, the 8-bit instruction code for the  
instruction is shifted in, with each bit being latched in  
on SI during the rising edge of SCK.  
Memory Type Memory Capacity  
4Ah  
20h  
14h  
16  
Rev. 0D May, 11, 2006  
ES25P80  
 复制成功!