ESMT
F49L320UA/F49L320BA
Operation Temperature Condition -40°C~85°C
The system can determine the status of the erase operation
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands
are ignored. Note that a hardware reset during the sector
erase operation immediately terminates the operation.
The Sector Erase command sequence should be
reinitiated once the device has returned to reading array
data, to ensure the data integrity.
by using DQ7, DQ6, DQ2, or RY/
. See “Write Operation
BY
Status” section for more Information on these status bits.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are no
longer latched. See the Erase/Program Operations tables
in “AC Characteristics” for parameters.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are no
longer latched. The system can determine the status of
Sector Erase Command
the erase operation by using DQ7, DQ6, DQ2, or RY/
.
BY
(Refer to “Write Operation Status” section for more
information on these status bits.)
Sector erase is a six-bus cycle operation. The sector erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the address of the
sector to be erased, and the sector erase command.
Refer to the Erase/Program Operations tables in the “AC
Characteristics” section for parameters.
The device does not require the system to preprogram the
memory prior to erase. The Embedded Erase algorithm
automatically programs and verifies the sector for an all
zero data pattern prior to electrical erase. The system is
not required to provide any controls or timings during these
operations.
Sector Erase Suspend/Resume Command
The Erase Suspend command allows the system to
interrupt a sector erase operation and then read data
from, or program data to, any sector not selected for
erasure (The device “ erase suspends” all sect or
selected for erasure.). This command is valid only during
the sector erase operation, including the 50 µs time-out
period during the sector erase command sequence. The
Erase Suspend command is ignored if written during the
chip erase operation or Embedded Program algorithm.
Addresses are “don’t -cares” when writing the Erase
Suspend command as shown in Table 5.
After the command sequence is written, a sector erase
time-out of 50µ s begins. Driving the time-out period,
additional sector addresses and sector erase commands
may be written. Loading the sector erase buffer may be
done in any sequence, and the number of sectors may be
from one sector to all sectors. The time between these
additional cycles must be less than 50 ꢀs, otherwise the
last address and command might not be accepted, and
erasure may begin.
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum of
20µs to suspend the erase operation. However, when the
Erase Suspend command is written during the sector
erase time-out, the device immediately terminates the
time-out period and suspends the erase operation.
It is recommended that processor interrupts be disabled
during this time to ensure all commands are accepted. The
interrupts can be re-enabled after the last Sector Erase
command is written. If the time between additional sector
erase commands can be assumed to be less than 50 µ s,
the system need not monitor DQ3.
Reading at any address within erase-suspended sectors
produces status data on DQ7–DQ0. The system can use
DQ7, or DQ6 and DQ2 together, to determine if a sector is
actively erasing or is erase-suspended. See “Write
Operation Status” section for more information on these
status bits.
Any command other than Sector Erase or Erase Suspend
during the time-out period resets the device to reading
array data. The system must rewrite the command
sequence and any additional sector addresses and
commands.
After an erase-suspended program operation is complete,
the system can once again read array data within
non-suspended sectors. The system can determine the
status of the program operation using the DQ7 or DQ6
The system can monitor DQ3 to determine if the sector
erase timer has timed out. (See the “DQ3: Sector Erase
Timer” section.) The time-out begins from the rising edge
of the final WE pulse in the command sequence.
Elite Semiconductor Memory Technology Inc.
Publication Date : Sep. 2008
Revision: 1.1
16/55