ESMT
F25L04UA
ELECTRICAL SPECIFICATIONS
Absolute Maximum Stress Ratings
(Applied conditions greater than those listed under “Absolute Maximum Stress Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at these conditions or conditions greater than those defined in the
operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating conditions may affect device
reliability.)
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C
D. C. Voltage on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VDD+0.5V
Transient Voltage (<20 ns) on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . -2.0V to VDD+2.0V
Package Power Dissipation Capability (Ta = 25°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0W
Surface Mount Lead Soldering Temperature (3 Seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240°C
Output Short Circuit Current (Note1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Note : 1. Output shorted for no more than one second. No more than one output shorted at a time.
AC CONDITIONS OF TEST
Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. <5 ns
Output Load . . . . . . . . . . . . . . . . . . . . . . . . CL = 15 pF for ≧75MHz
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CL = 30 pF for ≦50MHz
See Figures 19 and 20
OPERATING RANGE
Parameter
Symbol
VDD (for FCLK ≦ 75MHz)
DD (for FCLK = 100MHz)
Value
2.7~3.6
3.2~3.6
Unit
Operating Supply Voltage
V
V
Ambient Operating
Temperature
°C
TA
0~70
TABLE 7: DC OPERATING CHARACTERISTICS
Limits
Max
Symbol
Parameter
Read Current
Test Conditions
Min
Units
IDDR
IDDW
ISB
15
40
25
mA
CE =0.1 VDD/0.9 VDD@33 MHz, SO=open
CE =VDD
Program and Erase Current
Standby Current
mA
µA
CE =VDD, VIN=VDD or VSS
VIN=GND to VDD, VDD=VDD Max
VOUT=GND to VDD, VDD=VDD Max
VDD=VDD Min
ILI
Input Leakage Current
Output Leakage Current
Input Low Voltage
Input High Voltage
Output Low Voltage
1
1
0.8
µA
µA
V
V
V
ILO
VIL
VIH
VOL
0.7 VDD
VDD-0.2
VDD=VDD Max
IOL=100 µA, VDD=VDD Min
0.2
VOH
Output High Voltage
V
IOH=-100 µA, VDD=VDD Min
TABLE 8 : RECOMMENDED SYSTEM POWER-UP TIMINGS
Symbol
Parameter
Minimum
Units
µs
1
TPU-READ
VDD Min to Read Operation
VDD Min to Write Operation
10
10
1
TPU-WRITE
µs
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
TABLE 9: CAPACITANCE (TA = 25°C, f=1 Mhz, other pins open)
Parameter
Description
Test Condition
VOUT = 0V
Maximum
12 pF
1
COUT
Output Pin Capacitance
Input Capacitance
1
CIN
VIN = 0V
6 pF
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
Elite Semiconductor Memory Technology Inc.
Publication Date: Jan. 2009
Revision: 1.2 17/25
ESMT [ ELITE SEMICONDUCTOR MEMORY TECHNOLOGY INC. ]
