ES51967
6,600 Counts Auto DMM
Pin Description
Pin No
Symbol
Type
Description
1
2
3
4
5
6
7
V+
O
Output of on-chip DC-DC converter.
CREF+
CREF-
CINT
CAZ
I/O Positive connection for reference capacitor.
I/O Negative connection for reference capacitor.
O
I
O
O
Integrator output. Connect to integral capacitor
Auto-zero capacitor connection.
Buffer output pin. Connect to integral resistor
Buffer output pin in high-speed mode. Connect to high-speed integral
resistor.
BUFF
RAZ
8
9
IVSH
IVSL
OVX
OHMC
OVH
OVSG
OR1
VR5
VR4
VR3
VR2
I
I
I
O
I
I
O
O
O
O
O
High current measurement input.
Low current measurement input
10
11
12
13
14
15
16
17
18
19
20
Input high voltage for resistance measurement
Filter capacitor connection for resistance mode below 6.600MΩ range.
Output connection for resistance measurement
Sense low voltage for resistance measurement
Reference resistor connection for 660.0Ω range
Voltage measurement ÷10000 attenuator(1000V)
Voltage measurement ÷1000 attenuator(660.0V)
Voltage measurement ÷100 attenuator(66.00V)
Voltage measurement ÷10 attenuator(6.600V)
TEST5
ACVL
I/O Test pin
O
DC signal low input in ACV/ACA mode. Connect to negative output of
external AC to DC converter.
21
ACVH
O
DC signal high input in ACV/ACA mode. Connect to positive output of
external AC to DC converter.
22
23
24
25
26
27
ADI
ADO
ADOHZ
VRH
VR
I
O
I
O
I
Negative input of internal AC to DC OP Amp.
Output of internal AC to DC OP Amp.
Frequency input under voltage/current mode, offset to AGND.
Output of band-gap voltage reference. Typically –1.2V
Reference input voltage connection. Typically –400mV
For ADP mode. De-integrating voltage positive input. The input should
be higher than VA-.
VA+
I
28
VA-
I
For ADP mode. De-integrating voltage negative input. The input should
be lower than VA+.
29
30
31
32
33
ADP
SGND
OHMC1
VR1
I
G
O
I
Measurement input in ADP mode.
Signal Ground.
Filter capacitor connection for resistance mode under 660.0KΩ range.
Measurement input.
In capacitance mode, a compensation capacitor is connected.
In temperature mode, it is used to control decimal point.
In µA or mA modes, pull to V- to disable the ‘µ2’ or ‘m2’ sign on LCD.
Connect to a precise 9KΩ resister for capacitor measurement.
Connect to a precise 1KΩ resister for capacitor measurement.
VBAR
I
34
35
36
37
38
39
40
41
42
43
44
R9K
R1K
CA-
CA+
CSH+
CSH-
OHMC2
SLEEP
FREQ
RS232
DSHIFT
O
O
I/O Negative auto-zero capacitor connection for capacitor measurement
I/O Positive auto-zero capacitor connection for capacitor measurement
O
O
O
O
I
Filter capacitor connection for resistance mode under 66.00MΩ range.
Filter capacitor connection for resistance mode under 66.00MΩ range.
Filter capacitor connection for 6.600MΩ range in resistance mode.
Sleep mode indicator, asserts low in SLEEP mode.
Frequency counter input, offset V-/2 internally by the chip.
Assert low to enable serial data output.
I
I
Pull to V- to have 0.01MΩ resolution in 66.00MΩ.
Pull to DGND or keep it float will change the resolution to 66.0MΩ.
45
BKLIT
I
Back light function. Pulse low to set BKOUT pin output.
V2.6
3
08/10/06
CYRUSTEK [ Cyrustek corporation ]
