欢迎访问ic37.com |
会员登录 免费注册
发布采购

CX28395-19 参数 Datasheet PDF下载

CX28395-19图片预览
型号: CX28395-19
PDF下载: 下载PDF文件 查看货源
内容描述: 四核/ X16 /八路T1 / E1 / J1成帧器 [Quad/x16/Octal?T1/E1/J1 Framers]
分类和应用: 电信集成电路
文件页数/大小: 305 页 / 1863 K
品牌: CONEXANT [ CONEXANT SYSTEMS, INC ]
 浏览型号CX28395-19的Datasheet PDF文件第157页浏览型号CX28395-19的Datasheet PDF文件第158页浏览型号CX28395-19的Datasheet PDF文件第159页浏览型号CX28395-19的Datasheet PDF文件第160页浏览型号CX28395-19的Datasheet PDF文件第162页浏览型号CX28395-19的Datasheet PDF文件第163页浏览型号CX28395-19的Datasheet PDF文件第164页浏览型号CX28395-19的Datasheet PDF文件第165页  
CX28394/28395/28398  
3.0 Registers  
Quad/x16/OctalT1/E1/J1 Framers  
3.9 Receiver Registers  
RZCS  
Receive B8ZS/HDB3 Zero Code Substitution (affects only BPV/LCV/EXZ counting)—When  
set, the ZCS decoder does not include bipolar violations received as part of a B8ZS/HDB3  
code in the LCV error count [addr 054, 055]. Otherwise, all bipolar violations are counted.  
EXZ detection criteria is either 8 or 16 consecutive zeros, depending on RZCS configuration.  
0 = ZCS decoder reports all occurrences of BPV; also selects EXZ = 16 zeros  
1 = ZCS decoder does not report BPVs received as part of ZCS; also selects EXZ = 8 zeros  
041—Receive Test Pattern Configuration (RPATT)  
7
6
5
4
3
2
1
0
RESEED  
BSTART  
FRAMED  
ZLIMIT  
RPATT[1]  
RPATT[0]  
RESEED  
Reseed PRBS Sync Detector (auto clear)—If BSTART is active high, writing a one to  
RESEED forces the PRBS sync detector to reseed and search for test pattern sync [PSYNC;  
addr 00B]. The reseed and search algorithm remains active until test pattern sync is found.  
0 = no effect  
1 = reseed and search for test pattern sync  
BSTART  
Enable PRBS Detector and Start Counting PRBS Bit Errors—BERR [addr 058, 059] counting  
is enabled when BSTART is active high, and pattern sync is found [PSYNC=1; addr 00B].  
Otherwise, BERR counter holds its present value until cleared by a processor read.  
0 = PRBS detector disabled and BERR stops counting  
1 = enable PRBS detector and BERR counter  
FRAMED  
PRBS Framed—When set, PRBS test pattern bits are not checked during F-bit locations in T1  
mode or TS0 locations in E1 mode. Otherwise, test patterns are checked in all T1/E1 bit  
locations. FRAMED, ZLIMIT, and RPATT establish the test pattern measurement type as  
listed in Table 3-12.  
Table 3-12. Receive PRBS Test Pattern Measurements (1 of 2)  
FRAMED  
ZLIMIT  
RPATT  
00  
Test Pattern Measurements  
Unframed 211  
Inversion  
No  
0
0
0
0
0
0
0
0
1
1
0
0
0
0
1
1
1
1
0
0
Unframed 215  
01  
Yes  
No  
Unframed 220  
10  
Unframed 223  
11  
Yes  
No  
Unframed 211 with 7 zero limit  
Unframed 215 with 7 zero limit (non-std)  
Unframed 220 with 14 zero limit (QRSS/QRS/QRTS)  
Unframed 223 with 14 zero limit (non-std)  
Framed 211  
00  
01  
No  
10  
No  
11  
No  
00  
No  
Framed 215  
01  
Yes  
100054E  
Conexant  
3-39  
 
 复制成功!