Modulator Levels
Setting
Byte 1
MSB
7
0
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
MSB
7
0
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
6
0
2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
5
0
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
(Preceded by A/C12
H
)
Modulator Drives
First byte for transmission
Must be “0”
Mod. 1
Attenuation
12.4dB
12.0dB
11.6dB
11.2dB
10.8dB
10.4dB
10.0dB
9.6dB
9.2dB
8.8dB
8.4dB
8.0dB
7.6dB
7.2dB
6.8dB
6.4dB
6.0dB
5.6dB
5.2dB
4.8dB
4.4dB
4.0dB
3.6dB
3.2dB
2.8dB
2.4dB
2.0dB
1.6dB
1.2dB
0.8dB
0.4dB
0dB
Volume Set
Setting
MSB
7
0
0
5
0
1
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
6
0
1
(Preceded by A/C13
H
)
Volume Set
Transmitted First
Main Process Out
Enabled
Biased
Powersave
Chip Enabled
Powersaved
Volume Set
Attenuation
Off
48.0dB
46.4dB
44.8dB
43.2dB
41.6dB
40.0dB
38.4dB
36.8dB
35.2dB
33.6dB
32.0dB
30.4dB
28.8dB
27.2dB
25.6dB
24.0dB
22.4dB
20.8dB
19.2dB
17.6dB
16.0dB
14.4dB
12.8dB
11.2dB
9.6dB
8.0dB
6.4dB
4.8dB
3.2dB
1.6dB
0dB
Byte 0
6
0
2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
5
0
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Last byte for transmission
Must be “0”
Mod. 2
Attenuation
6.2dB
6.0dB
5.8dB
5.6dB
5.4dB
5.2dB
5.0dB
4.8dB
4.6dB
4.4dB
4.2dB
4.0dB
3.8dB
3.6dB
3.4dB
3.2dB
3.0dB
2.8dB
2.6dB
2.4dB
2.2dB
2.0dB
1.8dB
1.6dB
1.4dB
1.2dB
1.0dB
0.8dB
0.6dB
0.4dB
0.2dB
0dB
Table 5 Volume Set
Command Loading
Address/Commands and data bytes
must be loaded in accordance with the information given in
Figure 6 (Timing ).
The
Powersave
function is instigated by bit 5 of the
Volume Set Command (Table 5).
During Powersave, all internal elements except the Clock
Generator and “C-BUS” Interface are off, with the Mic Op-
Amp and Output Drive stage outputs connected to V
SS
.
Modulator Drives
are controlled separately, but the whole
two-byte Modulator Drive command must be loaded for each
required adjustment.
Chip Select
must be held at a logic “1” for the period
“t
CSOFF
” between transactions.
Table 4 Modulator Drive Levels
8
CMLMICRO [ CML MICROCIRCUITS ]
