欢迎访问ic37.com |
会员登录 免费注册
发布采购

CS4349-CZZ 参数 Datasheet PDF下载

CS4349-CZZ图片预览
型号: CS4349-CZZ
PDF下载: 下载PDF文件 查看货源
内容描述: 192 kHz的DAC W /音量控制和1 Vrms的@ 3.3 V [192 kHz DAC w/ Volume Control and 1 Vrms @ 3.3 V]
分类和应用:
文件页数/大小: 40 页 / 819 K
品牌: CIRRUS [ CIRRUS LOGIC ]
 浏览型号CS4349-CZZ的Datasheet PDF文件第18页浏览型号CS4349-CZZ的Datasheet PDF文件第19页浏览型号CS4349-CZZ的Datasheet PDF文件第20页浏览型号CS4349-CZZ的Datasheet PDF文件第21页浏览型号CS4349-CZZ的Datasheet PDF文件第23页浏览型号CS4349-CZZ的Datasheet PDF文件第24页浏览型号CS4349-CZZ的Datasheet PDF文件第25页浏览型号CS4349-CZZ的Datasheet PDF文件第26页  
CS4349  
4.6.2  
Control Port Mode  
1. Hold RST low until the power supply is stable and the left/right clock is fixed to the appropriate  
frequency, as discussed in Section 4.2. In this state, the control port is reset to its default settings, VQ  
will remain low, and VBIAS will be connected to VA.  
2. Bring RST high. The device will remain in a low-power state with VQ low.  
3. Perform a control port write to a valid register prior to the completion of approximately 512 LRCK  
cycles in Single-Speed Mode (1024 LRCK cycles in Double-Speed Mode, and 2048 LRCK cycles in  
Quad-Speed Mode). The desired register settings can be loaded while keeping the PDN bit set to 1.  
4. Set the PDN bit to 0. This will initiate the power-up sequence, which lasts approximately 50 µs when  
the Popguard is disabled. If the Popguard is enabled, see Section 4.7 for a complete description of  
power-up timing.  
4.7  
Popguard Transient Control  
The CS4349 uses a novel technique to minimize the effects of output transients during power-up and power-  
down. This technology, when used with external DC-blocking capacitors in series with the audio outputs,  
minimizes the audio transients commonly produced by single-ended single-supply converters. It is activated  
inside the DAC when the RST pin is toggled and requires no other external control, aside from choosing the  
appropriate DC-blocking capacitors.  
4.7.1  
4.7.2  
4.7.3  
Power-Up  
When the device is initially powered-up, the audio outputs, AOUTA and AOUTB, are clamped to GND.  
Following a delay of approximately 1000 sample periods, each output begins to ramp toward the quies-  
cent voltage. Approximately 10,000 LRCK cycles later, the outputs reach V and audio output begins.  
This gradual voltage ramping allows time for the external DC-blocking capacitors to charge to the quies-  
cent voltage, minimizing audible power-up transients.  
Q
Power-Down  
To prevent audible transients at power-down, the device must first enter its power-down state. When this  
occurs, audio output ceases and the internal output buffers are disconnected from AOUTA and AOUTB.  
In their place, a soft-start current sink is substituted that allows the DC-blocking capacitors to slowly dis-  
charge. Once this charge is dissipated, the power to the device may be turned off, and the system is ready  
for the next power-on.  
Discharge Time  
To prevent an audio transient at the next power-on, the DC-blocking capacitors must fully discharge be-  
fore turning on the power or exiting the power-down state. If full discharge does not occur, a transient will  
occur when the audio outputs are initially clamped to GND. The time that the device must remain in the  
power-down state is related to the value of the DC-blocking capacitance and the output load. For example,  
with a 3.3 µF capacitor, the minimum power-down time will be approximately 0.4 seconds.  
22  
DS782F1