PEM
AS28F128J3M
Q-Flash
Austin Semiconductor, Inc.
Bus Operations:
MODE
RP\
CE0
CE1
CE2
OE\
WE\
VPEN
DQ
NOTES ADDRESS
STS Default Mode
Read Array
Output Disable
Standby
Reset/Power-Down
Read Identifier Codes
Read Query
Read Status (ISM off)
Read Status (ISN on)
Write
VIH
VIH
VIH
VIL
VIH
VIH
VIH
VIH
VIH
Enabled Enabled Enabled
Enabled Enabled Enabled
Disabled Disabled Disabled
VIL
VIH
X
VIH
VIH
X
X
X
X
X
X
X
X
Dout
1,2,3
X
X
X
X
High-Z (VOH with External PU)
High-Z
High-Z
High-Z
X
X
X
X
X
X
X
High-Z (VOH with External PU)
High-Z (VOH with External PU)
High-Z (VOH with External PU)
Enabled Enabled Enabled
Enabled Enabled Enabled
Enabled Enabled Enabled
Enabled Enabled Enabled
Enabled Enabled Enabled
VIL
VIL
VIL
VIL
VIH
VIH
VIH
VIH
VIH
VIL
4
5
See Figure 7 of Micron DS
See Figure 7 of Micron DS
X
X
X
X
X
X
.
X
Dout
Din
VPENH
3,6,7
Notes
1
2
3
Refer to DC Characteristics. When VPEN</= VPENLK, memory contents can be read but not altered
X can be VIL or VIH for control and address pins, and VPENLK or VPENH for VPEN. See DC Characteristics for VPENLK and VPENH voltages
In default mode, STA is VOL when the ISM is executing internal Block Erase, Program, or lock bit configuration algorithms. It is VOH when the ISM
is not busy, in block erase suspend mode, program suspend mode, or reset/power-down mode.
See Read Identifier codes of the Micron Datasheet (DS)
See Read Query Mode Command section of the Micron Datasheet (DS)
Command Writes involving block erase, program, or lock bit configuration are reliably executed when VPEN=VPENH and VCC is within Specification
Refer to Table 4 on page 15 of the Micron Datasheet (DS)
4
5
6
7
DC Electrical Characteristics:
(VDD=3.0v-5%/+10%,TA=Min/Max temperatures of Operational
Range chosen)
Symbol
Parameter
Supply Voltage
Isolated Input/Output Supply
Input Load Current
Test Conditions
Min
Max
Units
Notes
Vcc
VccQ
ILI
2.7
2.7
3.6
3.6
+/- 1.0
V
V
uA
Vin=VccQ or GND, VCC=VCC Max., VCCQ = VCCQ Max
Vin=VccQ or GND, VCC=VCC Max., VCCQ = VCCQ Max
ILO
VIL
VIH
Output Leakage Current
Input Low Voltage
Input High Voltage
+/-10.0
0.8
VCCQ+0.5
0.4
uA
V
V
V
V
-0.5
2
1
1
VccQ=VccQ (MIN), IOL = 2mA
VccQ=VccQ (MIN), IOL = 100uA
VccQ=VccQ (MIN), IOH = 2.5mA
VccQ=VccQ (MIN), IOH = 100uA
VOL
VOH
Output Low Voltage
Output High Voltage
1,2
1
0.2
0.85xVCCQ
VCCQ-0.2
V
V
VPENLK
VPENH
VLKO
Program Voltage Lockout
Program Voltage
Vcc Lockout Voltage
Standby Current
0.8
3.6
V
V
V
uA
uA
uA
3,4,5
4,5,6
1
2.2
50
90
50
CMOS Inputs; VCC= VCC (MAX), Device Enabled, RP\=VCCQ+/-0.2v
TTL Inputs; VCC=VCC (MAX): Device Enabled, RP\=VIH
RP\=GND,+/-0.2V; IOUT (STS)=0mA
ICC1
220
2000
120
ICC2
ICC3
Power-Down Current
CMOS Inputs; VCC=VCC(MAX); VCCQ=VCCQ(MAX) using standard 4-word
page mode READS; Device is enabled; f=5MHz; IOUT=0mA
CMOS Inputs; Vcc=Vcc(MAX); VCCQ=VCCQ(MAX) using standard 4-word
page mode READS; Device is enabled; Ff=33MHz; IOUT=0mA
CMOS Inputs; VCC=VCC(MAX); VCCQ=VCCQ(MAX) using standard work/byte
single READS; Device Enabled; f=5MHz; IOUT=0mA
CMOS Inputs, VPEN=VCC
3
8
9
10
15
50
mA
mA
mA
mA
mA
Page Mode READ Current
Asynchronous READ Mode
Current
PROGRAM or set LOCK BITS
Current
BLOCL ERASE or CLEAR
BLOCK LOCK bits Current
PROGRAM SUSPEND or
BLOCK ERASE SUSPEND
Current
ICC4
ICC5
ICC6
17
17
17
17
60
70
70
80
TTL Inputs, VPEN=VCC
CMOS Inputs, VPEN=VCC
TTL Inputs, VPEN=VCC
Device is Disabled
ICC7
10
mA
Notes
[1]
[2]
[3]
Sampled, not 100% tested
Includes STS
ICCWS and ICCES are specified with the device deselected. If the device is read or written while in ERASE SUSPEND mode,
the device's curent draw is ICCR or ICCW
[4]
BLOCK ERASE, PROGRAMMING, and LOCK BIT configurations are inhibited when VPEN</= VPENLK, and they are not
guaranteed in the range betwwn VPENLK (MAX) and VPENH (MIN), or above VPENH (Max)
Typically, VPEN is connected to VCC
[5]
[6]
VPENH (MIN) = 2.7v
AS28F128J3MRG
Austin Semiconductor, Inc. reserves the right to change products or modify product specifications with appropriate notification
Revision 5.0 11/23/04
For Additional Products and Information visit out Web site at www.austinsemiconductor.com
4