12
Measurement parameters and measurement conditions
Speed and accuracy
FAST/MED/SLOW/SLOW2
Measurement speed
Rs
Rp
Ls
Lp
Cs
Cp
D
Equivalent series resistance (ESR)
Equivalent parallel resistance
Equivalent series inductance
Equivalent parallel inductance
Equivalent series capacitance
Equivalent parallel capacitance
Loss factor tan δ
Z
Y
θ
X
G
B
Q
Rdc
Impedance
Admittance
Phase angle
Reactance
Conductance
Susceptance
Q-factor
Averaging
Valid setting range: 1 to 256 (in steps of 1)
Z: 0.05% rdg. θ: 0.03° (representative value)
Basic accuracy
Guaranteed
accuracy range
Measurement
parameters
1 mΩ to 200 MΩ (impedance)
Guaranteed
accuracy period
1 year
σ
ε
Conductivity
Permittivity
DC resistance
Warm-up time
60 minutes
Terminal structure
4-terminal structure
Rs ±(0.00 m to 9.99999 G
Rp ±(0.00 m to 9.99999 G
)
)
Ω
Ω
Z
Y
θ
X
G
B
Q
Rdc
0.00 m to 9.99999 G
Ω
0.000 n to 9.99999 GS
±(0.000° to 999.999°)
±(0.00 m to 9.99999 G
±(0.000 n to 9.99999 GS)
±(0.000 n to 9.99999 GS)
±(0.00 to 9999.99)
Ls ±(0.00000 μ to 9.99999 GH)
Lp ±(0.00000 μ to 9.99999 GH)
Cs ±(0.0000 p to 9.99999 GF)
Cp ±(0.0000 p to 9.99999 GF)
Supplementary functionality
Uses a specific signal to time the start of measurement.
[Trigger types]
Internal trigger: Automatically generates a trigger signal
internally to repeat measurement.
External trigger: Allows you to control the instrument s
measurement operation by inputting a trigger signal from
an external device (trigger sources: manual, communica-
)
Ω
Display range
D
±(0.00000 to 9.99999)
Δ% ±(0.000% to 999.999%
)
,
±(0.00 m to 9.99999 G
)
Ω
σ
ε
±(0.00000 to 999.999 G)
±(0.00000 to 999.999 G)
tions commands, EXT. I/O)
[Trigger delay]
Sets the delay time from trigger input to measurement.
Setting range: 0.0000 s to 9.9999 s
[Trigger synchronous output]
.
1 mΩ to 200 MΩ
Measurable range
Output impedance
Range
Trigger function
Normal mode: 100 Ω, Low impedance high accuracy mode: 10Ω
4 Hz to 8 MHz
Outputs the measurement signal after trigger input and ap-
plies it to the sample during measurement only.
Allows you to set a wait time until data is acquired.
Setting range: 0.0000 s to 9.9999 s
4.00 Hz to 999.99 Hz …………… 10 mHz steps
1.0000 kHz to 9.9999 kHz …… 100 mHz steps
10.000 kHz to 99.999 kHz …… 1 Hz steps
100.00 kHz to 999.99 kHz …… 10 Hz steps
1.0000 MHz to 8.0000 MHz …… 100 Hz steps
Measurement
Resolution
frequency
[Open/short compensation]
[Load compensation] Number of sets of compensation condi-
tions: Up to 5
[Cable length compensation] Cable length settings: 0 m, 1 m,
2 m, 4 m
[Correlation compensation] Compensation of display
values based on user-input compensation coefficient
Accuracy
±0.01% of setting or less
Compensation
function
[Normal mode]
Measurement
4 Hz to 1.0000 MHz: 10 mV to 5 V (maximum 50 mA)
1.0001 MHz to 8 MHz: 10 mV to 1 V (maximum 10mA)
[Low impedance high accuracy mode]
signal level
[V mode]
Range
[4-terminal contact check]
Performs a contact (disconnection) check between HCUR and
HPOT and between LCUR and LPOT.
[High-Z reject function]
Detection of OPEN state during 2-terminal measurement.
[CV mode]
4 Hz to 1.0000 MHz: 10 mV to 1 V (maximum 100 mA)
Contact check
10 mV to 1.000 V …… 1 mV steps
Resolution
[Normal mode]
4 Hz to 1.0000 MHz: 10 μA to 50 mA (maximum 5 V)
1.0001 MHz to 8 MHz: 10 μA to 1 mA (maximum 1 V)
[Low impedance high accuracy mode]
Measurement
signal level
[CC mode]
Range
Recording and interface
Measurement result items (maximum 32000 items) can
4 Hz to 1.0000 MHz: 10 μA to 100 mA (maximum 1 V)
be saved to the instrument.
Memory can be read using communications commands
or a USB flash drive.
Memory function
10 μA steps
Resolution
Monitor voltage range: 0.000 V to 5.000 V
Monitor current range: 0.000 mA to 100.0 mA
Monitor function
Panel save and load Measurement conditions: Up to 60
Compensation values: Up to 128
functions
DC resistance
measurement
EXT. I/O( HANDLER) ,USB, USB flash drive, LAN,
GP-IB, RS-232C
Measurement signal level: Fixed at 1 V
Interfaces
Generating range: DC voltage 0 V to 2.50 V (10mV resolution)
In low Z high accuracy mode: 0 V to 1 V (10 mV resolution)
[Output from EXT. I/O connector]
Generates BCD output for the No.1 and No.3 parameter
measured values.
DC bias measurement
BCD output
*Input and output signals are set to BCD mode (selection
with judgment output).
Measurement modes
Display and sound
LCR mode: Measurement using a single set of conditions.
Measurement modes Continuous measurement mode: Continuous measurement
using previously saved conditions
Lock operation of the instrument using the touch screen.
Key lock function
Unlock by entering a passcode.
Beep tone
Enable or disable for judgment results and key operation.
LCD display on/off
Off: The display turns off 10 sec. after the touch panel is
last touched.
LCR mode
Display settings
Bin measurement: 10 categories for 2 measurement parameters
Judgment method: Set as absolute values, percentage, or
deviation percentage
Display
5.7-inch color TFT with touch panel
Other
Operating
temperature and
humidity
Measurements
Comparator measurement: Hi, IN, and Lo judgments for
2 parameters
Judgment method: Set as absolute values, percentage, or de-
viation percentage
0°C to 40°C (32°F to 104°F), 80% RH, non-condensing
Storage
temperature and
humidity
Zoom display function: Enlarged display of measured values
Number of display digits setting: Allows you to set the number
of display digits for measured values for each measurement
parameter. (Valid setting range: 3 to 6 digits)
-10°C to 50°C (14°F to 122°F), 80% RH, non-condensing
Display
Operating
environment
Indoors, Pollution Degree 2, altitude up to 2000 m (6562-ft.)
Power supply and
maximum rated
power
100 V AC to 240 V AC (50/60 Hz), 50 VA
Continuous measurement mode
Performs continuous measurement using measurement condi-
tions that have been saved using the panel save function.
Measurement is started by an external trigger (any of the three
Dielectric strength
Standards compliance
1.62 kV AC for 1 min. between power line and ground line
Measurements
EMC: EN 61326, EN 61000
Safety: EN 61010
types described below)
Approx. 330 W × 119 H × 230 D mm (12.99 W × 4.69
H × 9.06 D in) , approx. 4.2 kg (148.1 oz.)
Maximum number
60
Dimensions and Mass
of measurements
Power cord ×1, Instruction manual ×1,
Accessories
LCR application disc (Communications user manual) ×1
ASM-SENSOR [ ASM GMBH ]
