AS1152
austriamicrosystems
Data Sheet
Switching Characteristics
Switching Characteristics
(VCC = +3.0 to +3.6V, RL = 100Ω ±1%, f ≤ 150MHz, TA = -40 to +85°C
Typical values are at VCC = +3.3V, TA = +25ºC, Unless Otherwise Noted.)
1, 2, 3
Table 3. Switching Characteristics
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Differential Propagation Delay,
High-to-Low
Figure 18 on page 11 and
Figure 19 on page 11
tPHLD
1.1
1.7
ns
Differential Propagation Delay,
Low-to-High
Figure 18 on page 11 and
Figure 19 on page 11
tPLHD
tSKD1
tSKD2
tSKD3
tSKD4
tTLH
1.1
1.7
0.35
0.60
0.8
1.0
2.6
2.6
4
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Figure 18 on page 11 and
Figure 19 on page 11
Differential Pulse Skew 4
Differential Channel-to-Channel Skew 5
Differential Part-to-Part Skew 6
Differential Part-to-Part Skew 7
Rise Time
0.04
0.07
0.13
0.43
0.39
0.39
3
Figure 18 on page 11 and
Figure 19 on page 11
Figure 18 on page 11 and
Figure 19 on page 11
Figure 18 on page 11 and
Figure 19 on page 11
Figure 18 on page 11 and
Figure 19 on page 11
0.2
0.2
Figure 18 on page 11 and
Figure 19 on page 11
Fall Time
tTHL
Figure 21 on page 12 and
Figure 22 on page 12
Disable Time, High-to-Z
Disable Time, Low-to-Z
Enable Time, Z-to-High
tPHZ
Figure 21 on page 12 and
Figure 22 on page 12
tPLZ
3
4
Figure 21 on page 12 and
Figure 22 on page 12
tPZH
2
3
Figure 21 on page 12 and
Figure 22 on page 12
Enable Time, Z-to-Low
tPZL
2
3
ns
Maximum Operating Frequency 8, 9
fMAX
250
MHz
Notes:
1. Parameters are guaranteed by design and characterization.
2. CL includes probe and jig capacitance.
3. Signal generator conditions for dynamic tests: VOL = 0, VOH = 3V, f = 100MHz, 50% duty cycle, RO = 50Ω,
tR ≤ 1ns, tF ≤ 1ns (0 to 100%).
4. tSKD1 is the magnitude difference of differential propagation delay. tSKD1 = |tPHLD - tPLHD|.
5. tSKD2 is the magnitude difference of tPHLD or tPLHD of one channel to the tPHLD or tPLHD of another channel on
the same device.
6. tSKD3 is the magnitude difference of any differential propagation delays between devices at the same VCC and
within 5°C of each other.
7. tSKD4 is the magnitude difference of any differential propagation delays between devices operating over the
rated supply and temperature ranges.
8. fMAX signal generator conditions: VOL = 0, VOH = 3V, 50% duty cycle, RO = 50Ω,
tR ≤ 1ns, tF ≤ 1ns (0 to 100%).
9. Conforms to ANSI TIA/EIA 644 LVDS Standards ≤150MHz. Maximum operating frequency of 250MHz is pos-
sible using an AS1150 receiver.
www.austriamicrosystems.com
Revision 1.00
4 - 15