欢迎访问ic37.com |
会员登录 免费注册
发布采购

ELANSC400-66AC 参数 Datasheet PDF下载

ELANSC400-66AC图片预览
型号: ELANSC400-66AC
PDF下载: 下载PDF文件 查看货源
内容描述: 单芯片,低功耗, PC / AT兼容的微控制器 [Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers]
分类和应用: 微控制器PC
文件页数/大小: 132 页 / 2249 K
品牌: AMD [ AMD ]
 浏览型号ELANSC400-66AC的Datasheet PDF文件第47页浏览型号ELANSC400-66AC的Datasheet PDF文件第48页浏览型号ELANSC400-66AC的Datasheet PDF文件第49页浏览型号ELANSC400-66AC的Datasheet PDF文件第50页浏览型号ELANSC400-66AC的Datasheet PDF文件第52页浏览型号ELANSC400-66AC的Datasheet PDF文件第53页浏览型号ELANSC400-66AC的Datasheet PDF文件第54页浏览型号ELANSC400-66AC的Datasheet PDF文件第55页  
Table 10. Pin State Table—GPIOs/System Data (SD) Buffer Control  
Signal Name  
[Alternate  
Function]  
Max  
Load Supply  
(pF)  
Power  
Down Note 5 V  
Group  
Pin  
#
Output  
Drive  
Reset  
State Operation  
Normal  
Suspend  
State  
Type  
1
GPIO_CS2  
[[DBUFRDL]]  
C18  
D17  
C4  
B
[[O]]  
C
C
C
C
50  
VCC  
VCC  
VCC  
VCC  
I-PU  
I-PU  
I-PU  
I-PU  
I-PPU[O]  
O
I-PPU[O]  
TS-PD  
1
1
GPIO_CS3  
[[DBUFRDH]]  
B
[[O]]  
50  
I-PPU[O]  
O
I-PPU[O]  
TS-PD  
GPIO_CS4  
[[DBUFOE]]  
B
[[O]]  
50  
I-PPU[O]  
O
I-PPU[O]  
H[TS-PD][TS]  
I
I
S
S
2
KBD_ROW13  
[[R32BFOE]]  
A3  
STI-OD  
[O]  
250  
IOD-PU  
O
I-PU  
H[TS-PD][TS]  
Notes:  
1. The data buffer control signals are shared with the GPIO_CS4–GPIO_CS2 signals and with the keyboard row signal:  
When the data buffer control signals are enabled on the pins, they will drive inactive during Suspend mode, go three-state  
without resistors to allow an external resistor to 5 V, or three-state with a pulldown to support powering off the data buffer.  
Summary: GPIO_CS4–GPIO_CS2/DBUFOE/DBUFRDH/DBUFRDL: Built-in pullup and pulldown resistors that are invoked by:  
–Reset invokes pullup.  
–When buffer control is invoked by the configuration pin, these pins are outputs without any pullups or pulldowns.  
–When buffer control is enabled and in Suspend mode, DBUFRDH and DBUFRDL are three-state with the pulldowns  
enabled; DBUFOE has three options:  
•High (inactive) with no pullup or pulldown.  
•Three-state with a pulldown if it is programmed for the buffer to be powered off in Suspend mode (Power-Down Group I).  
•Three-state with no pulldown if it is programmed for the buffer to be powered on in Suspend mode and at 5 V.  
–When enabled as the GPIO_CS4–GPIO_CS2 signals:  
•As an output, the pullup and pulldown are disabled in all modes, and these GPIO_CS signals can be active in Suspend.  
•As an input, the pullup can be programmed to be enabled or disabled. This will then be the state of the pin in all  
modes, including Suspend.  
2. This data buffer control signal (R32BFOE) is shared with the keyboard row signal:  
When the data buffer control signals are enabled on the pins, they will drive inactive during Suspend mode, go three-state  
without resistors to allow an external resistor to 5 V, or three-state with a pulldown to support powering off the data buffer.  
Summary: KBD_ROW13/R32BFOE: Built-in pullup and pulldown resistors that are invoked by:  
–Reset invokes the pullup.  
–As R32BFOE, this pin is an output without a pullup or pulldown.  
–When buffer control is enabled and in Suspend mode, R32BFOE has three options:  
•High (inactive) with no pullup or pulldown.  
•Three-state with a pulldown if it is programmed for the buffer to be powered off in Suspend mode.  
•Three-state with no pulldown if it is programmed for the buffer to be powered on in Suspend mode and at 5 V.  
–When enabled as the keyboard row signal, this signal has a pullup enabled at all times.  
Élan™SC400 and ÉlanSC410 Microcontrollers Data Sheet  
51