[AK4671]
ABSOLUTE MAXIMUM RATINGS
(VSS1=VSS2=VSS3=VSS4=0V;
Parameter
Symbol
min
Power Supplies:
Analog
AVDD
−0.3
PLLBT
PVDD
−0.3
10bit SAR ADC
SAVDD
−0.3
Digital
DVDD
−0.3
Digital I/O 2
TVDD2
−0.3
Digital I/O 3
TVDD3
−0.3
Input Current, Any Pin Except Supplies
IIN
-
Analog Input Voltage 1 (Note
4)
VINA1
−0.3
Analog Input Voltage 2 (Note
5)
VINA2
−0.3
Digital Input Voltage 1 (Note
6)
VIND1
−0.3
Digital Input Voltage 2 (Note
7)
VIND2
−0.3
Digital Input Voltage 3 (Note
8)
VIND3
−0.3
Ambient Temperature (powered applied)
Ta
−30
Storage Temperature
Tstg
−65
max
4.0
4.0
4.0
4.0
4.0
4.0
±10
AVDD+0.3
SAVDD+0.3
DVDD+0.3
TVDD2+0.3
TVDD3+0.3
85
150
Units
V
V
V
V
V
V
mA
V
V
V
V
V
°C
°C
Note 2. All voltages with respect to ground.
Note 3. VSS1, VSS2, VSS3 and VSS4 must be connected to the same analog ground plane.
Note 4. RIN4/IN4−, LIN4/IN4+, RIN3/IN3−, LIN3/IN3+, RIN2/IN2−, LIN2/IN2+, RIN1/IN1−, LIN1/IN1+ pins
Note 5. SAIN1, SAIN2, SAIN3 pins
Note 6. PDN, I2C, CSN/CAD0, CCLK/SCL, CDTI/SDA, SDTI, LRCK, BICK, MCKI pins
Pull-up resistors at SDA and SCL pins should be connected to (DVDD+0.3)V or less voltage.
Note 7. BICKA, SYNCA, SDTIA pins
Note 8. BICKB, SYNCB, SDTIB pins
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS
(VSS1=VSS2=VSS3=VSS4=0V;
Parameter
Symbol
min
typ
Power Supplies Analog
AVDD
2.2
3.3
9)
PLLBT
PVDD
2.2
3.3
10bit SAR ADC
SAVDD
2.2
3.3
Digital
DVDD
1.6
3.3
Digital I/O 2
TVDD2
1.6
3.3
Digital I/O 3
TVDD3
1.6
3.3
Difference
0
AVDD−PVDD
−0.1
max
3.6
3.6
3.6
3.6
3.6
3.6
+0.1
Units
V
V
V
V
V
V
V
Note 9. The power-up sequence between AVDD, PVDD, SAVDD, DVDD, TVDD2 and TVDD3 is not critical.
The PDN pin should be held to “L” when power-up. The PDN pin should be set to “H” after all power supplies are
powered-up. The AK4671 should be operated by the recommended power-up/down sequence shown in “System
to avoid pop noise at receiver output, headphone output and
line output.
When the power is OFF partially except for DVDD, all power management bits (PMVCM, PMMP, PMMICL,
PMMICR, PMADL, PMADR, PMDAL, PMDAR, PMPLL, PMLOOPL, PMLOOPR, PMAINL1, PMAINR1,
PMAINL2, PMAINR2, PMAINL3, PMAINR3, PMAINL4, PMAINR4, PMLO1, PMRO1, PMLO2, PMRO2,
PMLO2S, PMRO2S, PMLO3, PMRO3, PMSRA, PMSRB, PMPCM, PMSAD) should be “0” or the PDN pin
should be “L”. DVDD should not be powered OFF while AVDD, PVDD, SAVDD, TVDD2 or TVDD3 is
powered ON. When only DVDD is OFF, the current of 10mA to 100mA around may occur.
* AKM assumes no responsibility for the usage beyond the conditions in this datasheet.
MS0666-E-02
-7-
2010/06
AKM [ ASAHI KASEI MICROSYSTEMS ]
