1.1 Hardware Interface
There are 8 configuration bits available in the CCR. However,
bits 7 and 6 are not used by the UT80CRH196KD. Bits 5 and 4
comprise the READY mode control which define internal limits
for waitstates generated by the READY pin. Bit 3 controls the
definition of the ALE/ADV pin for system memory controls
while bit 2 selects between the different write modes. Bit 1
selects whether the UT80CRH196KD will use a dynamic 16-
bit bus or whether it will be locked in as an 8-bit bus. Finally,
Bit 0 enables the Power Down mode and allows the user to
disable this mode for protection against inadvertent power
downs.
1.1.1 Interfacing with External Memory
The UT80CRH196KD can interface with a variety of external
memory devices. It supports either a fixed 8-bit bus width or a
dynamic 8-bit/16-bit bus width, internal READY control for
slow external memory devices, a bus-hold protocol that enables
external devices to take over the bus, and several bus-control
modes. These features provide a great deal of flexibility when
interfacing with external memory devices.
1.1.1.1 Chip Configuration Register
1.1.1.2 Bus Width and Memory Configurations
The Chip Configuration Register (CCR) is used to initialize the
UT80CRH196KD immediately after reset. The CCR is fetched
from external address 2018H (Chip Configuration Byte) after
removal of the reset signal. The Chip Configuration Byte (CCB)
is read as either an 8-bit or 16-bit word depending on the value
of the BUSWIDTH pin. The composition of the bits in the CCR
are shown in Table 4.
The UT80CRH196KD external bus can operate as either an 8-
bit or 16-bit multiplexed address/data bus (see figure 2). The
value of bit 1 in the CCR determines the bus operation. A logic
low value on CCR.1 locks the bus controller in 8-bit bus mode.
If, however, CCR.1 is a logic high, then the BUSWIDTH signal
is used to decide the width of the bus. The bus is 16 bits wide
when the BUSWIDTH signal is high, and is 8 bits when the
BUSWIDTH signal is low.
1.1.2 Reset
Table 4. Chip Configuration Register
To reset the UT80CRH196KD, hold the RESET pin low for at
least 16 state times after the power supply is within tolerance
and the oscillator has stabilized. Resets following the power-up
reset may be asserted for at least one state time, and the device
will turn on a pull-down transistor for 16 state times. This
enables the RESET signal to function as the system reset. The
reset state of the external I/O is shown in Table9,and the register
reset values are shown in Table 8.
Bit
7
Function
N/A
N/A
6
5
IRC1 - Internal READY Mode Control
IRC0 - Internal READY Mode Control
Address Valid Strobe Select (ALE/ADV)
Write Strobe Mode Select (WR and BHE/WRL and WRH)
Dynamic Bus Width Enable
4
3
2
1.1.3 Instruction Set
1
The instruction set for the UT80CRH196KD is compatible with
the industry standardMCS-96 instruction set used on the
8XC196KD.
0
Enable Power Down Mode
Table 5. Memory Map
Memory Description
External Memory1
Reserved
Begin
02080H
0205EH
02040H
02030H
02020H
02019H
02018H
02014H
02000H
00400H
0001AH
00000H
End
0FFFFH
0207FH
0205DH
0203FH
0202FH
0201FH
02018H
02017H
02013H
1FFFH
PTS Vectors
Upper Interrupt Vectors
Reserved
Reserved
Chip Configuration Byte
Reserved
Lower Interrupt Vectors
External Memory
Internal Memory (RAM)
Special Function Registers
003FFH
00019H
Notes:
1.The first instruction read following reset will be from location 2080h. All other external memory can be used as instruction and/or data memory.
3
AEROFLEX [ AEROFLEX CIRCUIT TECHNOLOGY ]
