AD7874
T he first read operation to the AD7874 after conversion always
accesses data from Data Register 1 (i.e., the conversion result
from the VIN1 input). INT is reset high on the falling edge of
RD during this first read operation. T he second read always ac-
cesses data from Data Register 2 and so on. T he address pointer
is reset to point to Data Register 1 on the rising edge of
CONVST. A read operation to the AD7874 should not be at-
tempted during conversion. T he timing diagram for the
AD7874 conversion sequence is shown in Figure 7.
TRACK/HOLDS GO
INTO HOLD
t1
tCONV
CONVST
INT
tACQUISITION
t5
t8
CS
RD
t2
t4
t7
t3
t6
CH1
DATA
CH4
DATA
CH2
DATA
CH3 HIGH-
HIGH-
Z
HIGH-
Z
HIGH-Z
HIGH-IMPEDANCE
DATA
DATA
Z
TIMES t2, t3, t4, t6, t7, AND t8 ARE THE SAME FOR ALL FOUR READ OPERATIONS.
Figure 7. AD7874 Tim ing Diagram
Figure 8. AD7874 FFT Plot
Effective Num ber of Bits
T he formula given in Equation 1 relates the SNR to the number
of bits. Rewriting the formula, as in Equation 2, it is possible to
get a measure of performance expressed in effective number of
bits (N).
AD 7874 D YNAMIC SP ECIFICATIO NS
T he AD7874 is specified and 100% tested for dynamic perfor-
mance specifications as well as traditional dc specifications such
as Integral and Differential Nonlinearity. T hese ac specifications
are required for the signal processing applications such as
phased array sonar, adaptive filters and spectrum analysis.
T hese applications require information on the ADC’s effect on
the spectral content of the input signal. Hence, the parameters
for which the AD7874 is specified include SNR, harmonic dis-
tortion, intermodulation distortion and peak harmonics. T hese
terms are discussed in more detail in the following sections.
SNR −1. 76
N =
(2)
6.02
T he effective number of bits for a device can be calculated di-
rectly from its measured SNR.
Figure 9 shows a typical plot of effective number of bits versus
frequency for an AD7874BN with a sampling frequency of
29 kHz. T he effective number of bits typically falls between
11.75 and 11.87 corresponding to SNR figures of 72.5 dB and
73.2 dB.
Signal-to-Noise Ratio (SNR)
SNR is the measured signal to noise ratio at the output of the
ADC. T he signal is the rms magnitude of the fundamental.
Noise is the rms sum of all the nonfundamental signals up to
half the sampling frequency (fs/2) excluding dc. SNR is depen-
dent upon the number of quantization levels used in the digiti-
zation process; the more levels, the smaller the quantization
noise. T he theoretical signal to noise ratio for a sine wave input
is given by
SNR = (6.02N + 1.76) dB
where N is the number of bits.
(1)
T hus for an ideal 12-bit converter, SNR = 74 dB.
T he output spectrum from the ADC is evaluated by applying a
sine wave signal of very low distortion to the VIN input which is
sampled at a 29 kHz sampling rate. A Fast Fourier T ransform
(FFT ) plot is generated from which the SNR data can be ob-
tained. Figure 8 shows a typical 2048 point FFT plot of the
AD7874BN with an input signal of 10 kHz and a sampling
frequency of 29 kHz. T he SNR obtained from this graph is
73.2 dB. It should be noted that the harmonics are taken into
account when calculating the SNR.
z
Figure 9. Effective Num bers of Bits vs. Frequency
–8–
REV. C
ADI [ ADI ]
