PRECISION ANALOG FRONT ENDS
TC500
TC500A
TC510
TC514
TC500/500A Negative Supply Voltage
GENERAL DESCRIPTION (Cont.)
(VSS to GND) ...................................................... – 8V
Analog Input Voltage (V+IN or V_IN) ....................VDD to VSS
Logic Input Voltage .................. VDD +0.3V to GND – 0.3V
Voltage on OSC ..... – 0.3V to (VDD +0.3V) for VDD < 5.5V
Ambient Operating Temperature Range ...... 0°C to +70°C
Storage Temperature Range ................ – 65°C to +150°C
Lead Temperature (Soldering, 10 sec) ................. +300°C
tainsthisstateuntilatransitionoccursontheCMPTRoutput,
at which time the processor halts its timer. The resulting
timer count is the converted analog data. Integrator Zero
(the final phase of conversion) removes any residue remain-
ing in the integrator in preparation for the next
conversion.
TheTC500/500A/510/514offerhighresolution(upto17
bits) superior 50Hz/60Hz noise rejection, low power opera-
tion, minimum I/O connections, low input bias currents and
lower cost compared to other converter technologies having
similar conversion speeds.
* Static-sensitive device. Unused devices must be stored in conductive
material. Protect devices from static discharge and static fields. Stresses
above those listed under "Absolute Maximum Ratings" may cause perma-
nent damage to the device. These are stress ratings only and functional
operation of the device at these or any other conditions above those
indicated in the operation sections of the specifications is not implied.
Exposuretoabsolutemaximumratingconditionsforextendedperiodsmay
affect device reliability.
ABSOLUTE MAXIMUM RATINGS*
TC510/514 Positive Supply Voltage
(VDD to GND) .................................................. +10.5V
TC500/500A Supply Voltage
(VDD to VSS) ....................................................... +18V
TC500/500A Positive Supply Voltage
(VDD to GND) ..................................................... +12V
ELECTRICAL CHARACTERISTICS: TC510/514: VDD = +5V, TC500/500A: VS = ±5V unless otherwise
specified. CAZ = CREF = 0.47 µF
TA = +25°C
TA = 0°C to +70°C
Symbol Parameter
Analog
Test Conditions
Min
Typ
Max
Min
Typ
Max
Unit
Resolution
Note 1
60
—
—
—
—
—
µV
ZSE
ENL
NL
Zero-Scale Error
with Auto Zero Phase
TC500/510/514
TC500A
—
—
—
—
0.005
0.003
—
—
0.005 0.012 % F.S.
0.003 0.009
End Point Linearity
TC500/510/514, Notes 1, 2,
TC500A
—
—
0.005
—
0.015
0.010
—
—
0.015 0.060 % F.S.
0.010 0.045 % F.S.
Best Case Straight
Line Linearity
TC500/510/514, Notes 1, 2,
TC500A
—
—
0.003
—
0.008
0.005
—
—
—
—
—
—
% F.S.
% F.S.
ZSTC
Zero-Scale
Temperature
Coefficient
Over Operating
Temperature Range
—
—
—
1
2
µV/°C
SYE
Full-Scale Symmetry
Error (Roll-Over Error)
Note 3
—
—
0.01
—
—
—
—
—
0.03
10
—
—
% F.S.
FSTC
Full-Scale Temperature Over Operating
ppm/°C
Coefficient
Temperature Range
External Reference
TC = 0ppm/°C
IIN
Input Current
VIN = 0V
—
6
—
—
—
—
—
pA
V
VCMR
Common-Mode
Voltage Range
VSS +1.5
—
VDD – 1.5 VSS +1.5
VDD – 1.5
Integrator Output Swing
VSS +0.9
VSS +1.5
VSS +1
—
—
—
VDD – 0.9 VSS +0.9
VDD – 1.5 VSS +1.5
—
—
—
VSS +0.9
VSS +1.5
VDD – 1
V
V
V
Analog Input Signal RangeACOM = GND = 0V
Voltage Reference Range V_REF V+REF
VREF
3-20
VDD – 1
VSS +1
TELCOM SEMICONDUCTOR, INC.