ESMT
M12S64164A
SIMPLIFIED TRUTH TABLE
BA0,
BA1
A11,
A9~A0
COMMAND
CKEn-1 CKEn
DQM
X
A10/AP
Note
CS RAS CAS
WE
L
Register
Refresh
Mode Register set
Auto Refresh
H
H
X
H
L
L
L
L
L
L
L
OP CODE
X
1,2
3
H
X
Entry
3
Self
Refresh
L
H
L
H
X
L
H
X
H
H
X
H
X
X
X
3
Exit
L
H
X
X
3
Bank Active & Row Addr.
H
V
V
Row Address
Column
Address
(A0~A7)
Column
Address
(A0~A7)
Auto Precharge Disable
Auto Precharge Enable
Auto Precharge Disable
Auto Precharge Enable
L
4
4,5
4
Read &
H
X
L
H
L
H
X
Column Address
H
L
Write &
H
H
H
X
X
X
L
L
L
H
H
L
L
H
H
L
L
L
X
X
X
V
Column Address
H
4,5
6
Burst Stop
Precharge
X
Bank Selection
All Banks
V
X
L
X
H
H
L
X
V
X
X
H
X
X
V
X
X
H
X
V
X
V
X
X
H
X
V
Entry
H
L
L
H
L
X
X
X
Clock Suspend or
Active Power Down
X
X
Exit
X
H
L
Entry
H
Precharge Power Down Mode
H
L
Exit
L
H
X
X
V
X
X
DQM
H
H
V
X
X
X
7
H
L
X
H
X
H
No Operating Command
H
(V = Valid, X = Don’t Care. H = Logic High, L = Logic Low)
Note:
1.OP Code : Operating Code
A0~A11 & BA0 ~ BA1: Program keys. (@ MRS)
2.MRS can be issued only at all banks precharge state.
A new command can be issued after 2 CLK cycles of MRS.
3.Auto refresh functions are as same as CBR refresh of DRAM.
The automatical precharge without row precharge of command is meant by “Auto”.
Auto/self refresh can be issued only at all banks idle state.
4. BA0 ~ BA1: Bank select addresses.
If both BA0 and BA1 are “Low” at read, write, row active and precharge, bank A is selected.
If both BA0 is “Low” and BA1 is “High” at read, write, row active and precharge, bank B is selected.
If both BA0 is “High” and BA1 is “Low” at read, write, row active and precharge, bank C is selected.
If both BA0 and BA1 are “High” at read, write, row active and precharge, bank D is selected
If A10/AP is “High” at row precharge , BA0 and BA1 is ignored and all banks are selected.
5.During burst read or write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
6.Burst stop command is valid at every burst length.
7.DQM sampled at positive going edge of a CLK and masks the data-in at the very CLK (Write DQM latency is 0), but
makes Hi-Z state the data-out of 2 CLK cycles after.(Read DQM latency is 2)
Elite Semiconductor Memory Technology Inc.
Publication Date: Apr. 2009
Revision: 1.2 7/45
ESMT [ ELITE SEMICONDUCTOR MEMORY TECHNOLOGY INC. ]
