CY7B991
CY7B992
[2, 13]
Switching Characteristics Over the Operating Range
[14]
[14]
CY7B991–2
CY7B992–2
Parameter
Description
FS = LOW
Min.
Typ.
Max.
Min.
Typ.
Max.
Unit
[1, 2]
[1, 2]
f
Operating Clock
15
25
30
50
80
15
30
50
MHz
NOM
Frequency in MHz
FS = MID
25
40
[1, 2 , 3]
[15]
FS = HIGH
40
80
t
t
t
t
REF Pulse Width HIGH
REF Pulse Width LOW
Programmable Skew Unit
5.0
5.0
5.0
ns
ns
RPWH
RPWL
U
5.0
See Table 1
Zero Output Matched-Pair Skew
0.05
0.20
0.05
0.20
ns
SKEWPR
[16, 17]
(XQ0, XQ1)
[16, 18,19]
t
t
Zero Output Skew (All Outputs)
0.1
0.25
0.5
0.1
0.25
0.5
ns
ns
SKEW0
Output Skew (Rise-Rise, Fall-Fall, Same
0.25
0.25
SKEW1
[16, 20]
Class Outputs)
t
t
t
Output Skew (Rise-Fall, Nominal-Inverted,
Divided-Divided)
0.3
0.25
0.5
0.5
0.5
0.9
0.3
0.25
0.5
0.5
0.5
0.7
ns
ns
ns
SKEW2
SKEW3
SKEW4
[16, 20]
Output Skew (Rise-Rise, Fall-Fall, Different
[16, 20]
Class Outputs)
Output Skew (Rise-Fall, Nominal-Divided,
[16, 20]
Divided-Inverted)
[14, 21]
t
t
t
t
t
t
t
t
t
Device-to-Device Skew
0.75
+0.25
+0.65
2.0
0.75
+0.25
+0.5
3.0
ns
ns
ns
ns
ns
ns
ns
ms
ps
ps
DEV
Propagation Delay, REF Rise to FB Rise
–0.25
–0.65
0.0
0.0
–0.25
–0.5
0.0
0.0
PD
[22]
Output Duty Cycle Variation
ODCV
PWH
PWL
ORISE
OFALL
LOCK
JR
[23, 24]
Output HIGH Time Deviation from 50%
[23, 24]
Output LOW Time Deviation from 50%
1.5
3.0
[23, 25]
Output Rise Time
0.15
0.15
1.0
1.0
1.2
0.5
0.5
2.0
2.0
2.5
[23, 25]
Output Fall Time
1.2
2.5
[26]
PLL Lock Time
0.5
0.5
[14]
Cycle-to-Cycle Output
Jitter
RMS
25
25
[14]
Peak-to-Peak
200
200
Note:
13. Test measurement levels for the CY7B991 are TTL levels (1.5V to 1.5V). Test measurement levels for the CY7B992 are CMOS levels (VCC/2 to VCC/2). Test
conditions assume signal transition times of 2 ns or less and output loading as shown in the AC Test Loads and Waveforms unless otherwise specified.
14. Guaranteed by statistical correlation. Tested initially and after any design or process changes that may affect these parameters.
15. Except as noted, all CY7B992–2 and –5 timing parameters are specified to 80-MHz with a 30-pF load.
16. SKEW is defined as the time between the earliest and the latest output transition among all outputs for which the same tU delay has been selected when all are
loaded with 50 pF and terminated with 50Ω to 2.06V (CY7B991) or VCC/2 (CY7B992).
17. tSKEWPR is defined as the skew between a pair of outputs (XQ0 and XQ1) when all eight outputs are selected for 0tU.
18. tSKEW0 is defined as the skew between outputs when they are selected for 0tU. Other outputs are divided or inverted but not shifted.
19. CL=0 pF. For CL=30 pF, tSKEW0=0.35 ns.
20. There are three classes of outputs: Nominal (multiple of tU delay), Inverted (4Q0 and 4Q1 only with 4F0 = 4F1 = HIGH), and Divided (3Qx and 4Qx only in Divide-by-2
or Divide-by-4 mode).
21. tDEV is the output-to-output skew between any two devices operating under the same conditions (VCC ambient temperature, air flow, etc.)
22. tODCV is the deviation of the output from a 50% duty cycle. Output pulse width variations are included in tSKEW2 and tSKEW4 specifications.
23. Specified with outputs loaded with 30 pF for the CY7B99X–2 and –5 devices and 50 pF for the CY7B99X–7 devices. Devices are terminated through 50Ω to
2.06V (CY7B991) or VCC/2 (CY7B992).
24. tPWH is measured at 2.0V for the CY7B991 and 0.8 VCC for the CY7B992. tPWL is measured at 0.8V for the CY7B991 and 0.2 VCC for the CY7B992.
25. tORISE and tOFALL measured between 0.8V and 2.0V for the CY7B991 or 0.8VCC and 0.2VCC for the CY7B992.
26. tLOCK is the time that is required before synchronization is achieved. This specification is valid only after VCC is stable and within normal operating limits. This parameter
is measured from the application of a new signal or frequency at REF or FB until tPD is within specified limits.
6
CYPRESS [ CYPRESS ]
