欢迎访问ic37.com |
会员登录 免费注册
发布采购

TP6312F 参数 Datasheet PDF下载

TP6312F图片预览
型号: TP6312F
PDF下载: 下载PDF文件 查看货源
内容描述: 1/4 〜1/ 11占空比VFD控制器/驱动器 [1/4 TO 1/11-DUTY VFD CONTROLLER/DRIVER]
分类和应用: 驱动器控制器
文件页数/大小: 9 页 / 500 K
品牌: ETC [ ETC ]
 浏览型号TP6312F的Datasheet PDF文件第1页浏览型号TP6312F的Datasheet PDF文件第2页浏览型号TP6312F的Datasheet PDF文件第4页浏览型号TP6312F的Datasheet PDF文件第5页浏览型号TP6312F的Datasheet PDF文件第6页浏览型号TP6312F的Datasheet PDF文件第7页浏览型号TP6312F的Datasheet PDF文件第8页浏览型号TP6312F的Datasheet PDF文件第9页  
TP6312  
1/4 TO 1/11-DUTY VFD CONTROLLER/DRIVER  
Functional Description  
The data of each Key is stored as illustrated below,  
Display RAM Address and Display Mode  
and is read by a read command, starting from the  
least significant bit.  
The display RAM stores the data transmitted from an  
external device to TP6312 through the serial interface,  
and is assigned addresses as follows, in units of 8  
bits:  
Key1  
Key4 Key1  
Key4  
Seg1 / KS1  
Seg2 / KS2  
Reading sequence  
Seg3 / KS3  
Seg5 / KS5  
Seg4 / KS4  
Seg6 / KS6  
Seg1  
00HL  
Seg4  
00HU  
Seg8  
Seg12  
Seg16  
DIG1  
01HL  
03HL  
05HL  
07HL  
09HL  
0BHL  
0DHL  
0FHL  
11HL  
13HL  
15HL  
01HU  
b0  
b3 b4  
b7  
02HL  
04HL  
06HL  
08HL  
0AHL  
0CHL  
0EHL  
10HL  
12HL  
14HL  
02HU  
04HU  
06HU  
08HU  
0AHU  
0CHU  
0EHU  
10HU  
12HU  
14HU  
03HU  
05HU  
07HU  
09HU  
0BHU  
0DHU  
0FHU  
11HU  
13HU  
15HU  
DIG2  
DIG3  
DIG4  
DIG5  
DIG6  
DIG7  
DIG8  
DIG9  
DIG10  
DIG11  
LED Port  
Data is written to the LED port by a write command,  
starting from the least significant bit of the port.  
When a bit of this port is 0, the corresponding LED  
lights; when the bit is 1, the LED goes off. The data  
of bits 5 through 8 is ignored.  
---- ---- ---- ----  
b3  
b2  
b1  
b0  
LED1  
LED2  
LED3  
LED4  
b0  
b3 b4  
b7  
Don't care  
XX HL  
XX HU  
Lower 4 bits Higher 4 bits.  
On power application, all LEDs are unlit.  
Key Matrix and Key-Input Data Storage  
RAM  
SW Data  
The SW data is read by a read command, starting  
from the least significant bit. Bits 5 through 8 of the  
SW data are 0.  
The Key matrix is of 6 × 4 configuration, as shown  
below.  
KEY1  
KEY2  
KEY3  
KEY4  
MSB  
0
LSB  
b0  
0
0
0
b3  
b2  
b1  
SW1  
SW2  
SW3  
SW4  
Commands  
A command sets the display mode and status of the  
VFD driver.  
The first 1 byte input to TP6312 through the DIN pin  
after the STB pin has fallen is regarded as a  
command.  
If STB is high while a command/data is transmitted,  
serial communication is initialized, and the  
transmitting command/data is invalid; however, the  
Version 1.1  
Page 3 of 9  
http://www.topro.com.tw  
September 2003