欢迎访问ic37.com |
会员登录 免费注册
发布采购

SL6609A 参数 Datasheet PDF下载

SL6609A图片预览
型号: SL6609A
PDF下载: 下载PDF文件 查看货源
内容描述: 直接转换FSK数据接收 [DIRECT CONVERSION FSK DATA RECEIVER]
分类和应用:
文件页数/大小: 20 页 / 507 K
品牌: ZARLINK [ ZARLINK SEMICONDUCTOR INC ]
 浏览型号SL6609A的Datasheet PDF文件第5页浏览型号SL6609A的Datasheet PDF文件第6页浏览型号SL6609A的Datasheet PDF文件第7页浏览型号SL6609A的Datasheet PDF文件第8页浏览型号SL6609A的Datasheet PDF文件第10页浏览型号SL6609A的Datasheet PDF文件第11页浏览型号SL6609A的Datasheet PDF文件第12页浏览型号SL6609A的Datasheet PDF文件第13页  
SL6609A  
COMPONENTS LIST FOR APPLICATION BOARD At 470MHz, 25kHz Channel Spacing.  
(LO circuit is 50Wnetwork as in Fig.5 - crystal oscillator not specified)  
Resistors  
C14  
C15  
C16  
C17  
C18  
C19  
C20  
C21  
C22  
C23  
C24  
C25  
C26  
C27  
C28  
C29  
C30  
C31  
C34  
VC1  
1n  
1n  
1n  
1n  
1n  
not used  
1n  
R1  
R2  
R3  
R4  
R5  
R6  
R7  
R8  
open circuit  
open circuit  
100  
100k  
100  
100  
100  
open circuit  
220k  
1n  
not used  
not used  
1n  
R9  
R10  
R11  
R12  
R13  
R14  
R15  
R16  
R17  
R18  
R22  
1M  
100k (2)  
300 (3)  
3k9 (1)  
1n  
open circuit  
not used  
not used  
100p  
2u2  
2u2  
1p5  
1-3pF  
4k7  
4k7  
33k  
open circuit (4)  
0R (4)  
open circuit  
Inductors  
Capacitors  
L1  
L2  
T1  
47nH (5)  
C1  
C2  
C3  
1n  
3.3pF  
1n  
not used (3)  
16nH 2 Turn 1:1 (Coilcraft) Q4123-A  
C4  
C5  
C6  
C7  
C8  
C9  
C10  
C11  
C12  
C13  
1n  
Active Components  
3.9pF  
2u2  
1n  
100n  
1n (2)  
2u2  
100n  
1n  
Q1  
Q2  
Q3  
Q4  
Q5  
D1  
Zetex FMMT589  
Philips BFT25A  
Not Used  
Philips BFT25A(3)  
Philips BFT25A  
Panasonic MA862(6)  
1n  
Notes  
1.  
2.  
The values of R13 is determined by the set-up proce-  
dure. See Application Note.  
Pin 9 (TCADJ) to VR (Pin 6) and by connecting Pin 28  
(IAGCOUT) to Vcc1, (R18). The voltage at Pin 8 may  
still be used as an RSSI. R9, C8, C14, C19, R17 and  
D1 may then be omitted.  
The value of "C9" is determined by the output data rate.  
Use 2nF for 512bps, 1nF for 1200bps and 470pF for  
2400bps.  
5.  
L1and C26 form the low noise matching network for the  
RF amplifier. The values given are for the RF amplifier  
specified in the Applications Circuit with no Audio AGC  
connected. i.e. R17 and D1 omitted.  
3.  
4.  
R12 & Q4 form a dummy load for the regulator.  
Permitted load currents for the regulator are 250µA to  
5mA. The 1V regulator (output Pin 23) can be switched  
off by connecting Pin 23 directly to VCC2. Q1, Q4, R12  
and C12 must then be omitted  
6.  
7.  
Suggested diode for use with the Audio AGC circuit  
(D1 is not included on the general demonstration  
circuit).  
L2 is used in the Audio AGC circuit (see Fig.6). For the  
characteristics of the Audio AGC current source see  
figure 7. If the Audio AGC is not required then the  
current source (Pin 28) may be disabled by connecting  
The value of R11 is dependent on the data output load.  
R11 should allow sufficient current to drive the data  
output load.  
8