KESRX04
Increasing the decay time constant of the AGC circuit by
increasing the value of C8 will impair the settling time (time to
good data) of the receiver. When duty cycling the operation to
thereceiverbetweenPD0andPD2tolowerpowerconsumption
of the receiver. When Duty cycling the receiver between PD1
and PD2 the settling time of the receiver is independent of C8.
In the application circuit Figure 11 the value of C8 is configured
for minimum settling time.
IF amp/RSSI detector
This is a log amplifier with a gain > 80dB and an RSSI
output used as the detector. The 3dB bandwidth of the IF log
amplifier is typically 20MHz to allow for high IF’s to be used.
However, normally, this wide IF bandwidth would limit the
overallsensitivityofthereceiverduetotheamplifiedwideband
noise generated in the first IF stage.
The RSSI detector is not frequency selective so that any
wide band noise introduced after the intermediate filter will be
detected as signal. A simple LC noise reduction filter is
therefore positioned part way down the log amplifier to reduce
the noise power from the earlier stages. Typically this filter
only needs to be a fixed component parallel LC filter (L5 // C7)
between pins IFFLT1 and IFFLT2 with a 1MHz bandwidth (i.e.
Q~10). There is an internal 20Kohm damping resistor across
these pins which will determine the Q and the choice of L and
Anti-jamming Circuit
TheoutputoftheRSSIisACcoupledintotheAnti-jamming
circuit where the signal is DC restored on the peak signal level
Figure 7. The coupling capacitor charges to the appropriate
DC level which is related to the final slice level for the data
comparator. The anti-jamming circuit amplifies the peak of the
signal to recover the data signal component even in the
presence of CW jamming signals. The interferer causes
modulation of the wanted signal at the beat frequency of the
two signals and reduces the amplitude of the wanted data
component making it more difficult to recover. By-passing the
anti-jam circuit Figure 8 will result in data corruption for
interfering RF signal levels 6dB below the wanted signal
(Figure 5A)
C values.
20000
Q
L =
C =
i.e.
2.π. fIF.Q;
2.π. fIF.20000
The DC restoration circuit has a fast attack time and slow
decay time, both controlled by the value of coupling capacitor
chosen between RSSI and DETB pins.
Figure 5 illustrates a suitable test setup for characterising
the interference rejection and selectivity of the receiver.
Figure5A illustratesthein-bandinterferencerejectionwith
the anti-jam circuit connected Figure 7 and by-passed(Figure
8) at 3V Tamb = 25°C. Note, the improvement in interference
rejection between the two modes of operation over the wanted
signal range of -94 to -20dBm.
Figure 5B illustrates the difference in receiver selectivity
with the ant-jam circuit connected (Figure 7) and by-passed
(Figure8).Note,theimprovementinreceiverselectivitybetween
the two modes of operation. The selectivity curve with the anti-
jam circuit by-passed is governed by the response of the front
end SAW filter, IF ceramic filter and data filter. Providing no
rejection for interfering signals within the pass band of the
receiver. Whereas the receiver with the anti-jam circuit
connected actively responds to the presence of the in-band
interferingsignaltorecoverthewantedOOKmodulatedsignal.
The action of the anti-jam circuit centres the bandwidth of the
receiveraroundthewantedsignalproportionaltothedatafilter
bandwidth to suppress the interfering beat frequency.
Figures 5A and 5B were recorded with the following
component specification.
An external damping resistor should not be used as this will
alter the gain of the log amplifier. A ceramic resonator or filter
is not a suitable component here as a low impedance dc path
must be maintained to remove dc voltage offsets in the high
gain log amplifier. Further improvement in sensitivity can be
gained by using a narrow band IF ceramic filter and a narrower
noise reduction filter.
For a low IF receiver, <1MHz, a low pass filter can be used
for both the IF and noise reduction filters. Such a receiver
however will have virtually no image rejection capability, and
will thus have a 3dB penality in noise factor impairing the
ultimate sensitivity of the receiver by a minimum of 3dB.
The RSSI output transfer characteristic, at pin RSSI, has a
slope of about 16mV/dB. A typical transfer characteristic from
RF in input to RSSI output is plotted in Figure 9B, measured
with a constant RF input signal. This shows the effect of the
AGC in extending the range of the detector to +10dBm RF
input signal and includes the effect of the AGC circuit adapting
to this signal level.
Because the RF amplifier AGC has a fast attack time - slow
decay time characteristic the gain of the stage remains con-
stant during the data burst. This means that the change in
output for a given extinction ratio also remains constant at
approximately16mV/dBuptopeakinputsignallevels>+10dBm.
This requires the decay time constant to exceed the transmit-
tedbitperiod andnolongperiodofzerosignalpowerhasbeen
transmitted.
Component Specification (Figure 7)
Anti-Jam removed (Figure 8)
R6
C2
130KΩ
270pF
R6
C2
12KΩ
removed
Data Filter BW
IFBW
5kHz
470kHz
Data Filter BW
IF BW
5kHz
470kHz
SAW BW
OOK modulation
750kHz
4kB/s (50% duty cycle)
SAW BW
OOK modulation
750kHz
4kB/S (50% duty cycle)
Component specification for Figure 5A and 5B
8
ZARLINK [ ZARLINK SEMICONDUCTOR INC ]
