X25057
ABSOLUTE MAXIMUM RATINGS*
*COMMENT
Temperature under Bias................... –65°C to +135°C
Storage Temperature ....................... –65°C to +150°C
Voltage on any Pin with
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation of
the device at these or any other conditions above those
indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating con-
ditions for extended periods may affect device reliability.
Respect to V ................................... –1V to +7V
SS
D.C. Output Current..............................................5mA
Lead Temperature
(Soldering, 10 seconds).............................. 300°C
RECOMMENDED OPERATING CONDITIONS
Supply Voltage
X25057
Limits
Temperature
Commercial
Industrial
Min.
0°C
Max.
+70°C
+85°C
4.5V to 5.5V
2.7V to 5.5V
1.8V to 3.6V
X25057-2.7
X25057-1.8
–40°C
7033 FRM T04
7033 FRM T05
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions, unless otherwise specified.)
Limits
Symbol
Parameter
Min.
Max.
Units
Test Conditions
I
V
Supply Current (Write)
3
mA SCK = V
x 0.1/V
CC
x 0.9 @ 5MHz,
CC1
CC
CC
SO = Open, CS = V
SS
I
I
V
V
Supply Current (Read )
Supply Current
400
1
µA
µA
SCK = V
SO = Open, CS = V
x 0.1/V
x 0.9 @ 5MHz,
CC2
CC
CC
CC
SS
CS = V , V = V or V
CC
SB
CC
CC IN
SS
(Standby)
I
I
Input Leakage Current
Output Leakage Current
Input LOW Voltage
Input HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Output LOW Voltage
Output HIGH Voltage
Output HIGH Voltage
Output HIGH Voltage
10
10
µA
µA
V
V
V
= V to V
SS
CC
LI
IN
= V to V
CC
LO
OUT
SS
(1)
V
V
V
V
V
V
V
V
–0.5
V
x 0.3
IL
CC
(1)
V
x 0.7
V
+ 0.5
V
IH
CC
CC
0.4
V
V
> 3.3V, I = 2.1mA
OL1
OL2
OL3
OH1
OH2
OH3
CC OL
0.4
0.4
V
2V < V
≤ 3.3V, I = 1mA
CC OL
V
V
V
≤ 2V, I = 0.5mA
OL
CC
V
V
V
– 0.8
– 0.4
– 0.2
V
> 3.3V, I
= -1.0mA
CC
CC
CC
CC
OH
V
2V < V
≤ 3.3V, I
= -0.4mA
CC
OH
V
V
≤ 2V, I
= -0.25mA
CC
OH
7033 FRM T06
POWER-UPTIMING
Symbol
Parameter
Power-up to Read Operation
Power-up to Write Operation
Min.
Max.
Units
(2)
PUR
t
t
1
5
ms
(2)
PUW
ms
7033 FRM T07
Notes: (1) V Min. and V Max. are for reference only and are not 100% tested.
IL
IH
(2) t
and t
are the delays required from the time V
is stable until the specified operation can be initiated. These parameters
CC
PUR
PUW
are periodically sampled and not 100% tested.
8
XICOR [ XICOR INC. ]
