欢迎访问ic37.com |
会员登录 免费注册
发布采购

WM8523GEFL/V 参数 Datasheet PDF下载

WM8523GEFL/V图片预览
型号: WM8523GEFL/V
PDF下载: 下载PDF文件 查看货源
内容描述: [24-bit 192kHz Stereo DAC with 2Vrms Ground Referenced Line Output]
分类和应用: 转换器
文件页数/大小: 51 页 / 618 K
品牌: WOLFSON [ WOLFSON MICROELECTRONICS PLC ]
 浏览型号WM8523GEFL/V的Datasheet PDF文件第5页浏览型号WM8523GEFL/V的Datasheet PDF文件第6页浏览型号WM8523GEFL/V的Datasheet PDF文件第7页浏览型号WM8523GEFL/V的Datasheet PDF文件第8页浏览型号WM8523GEFL/V的Datasheet PDF文件第10页浏览型号WM8523GEFL/V的Datasheet PDF文件第11页浏览型号WM8523GEFL/V的Datasheet PDF文件第12页浏览型号WM8523GEFL/V的Datasheet PDF文件第13页  
Production Data  
WM8523  
ELECTRICAL CHARACTERISTICS  
Test Conditions  
LINEVDD=AVDD=3.3V, LINEGND=AGND=0V, TA=+25°C, Slave Mode, fs=48kHz, MCLK=256fs, 24-bit data, unless otherwise  
stated.  
PARAMETER  
SYMBOL  
TEST CONDITIONS  
MIN  
TYP  
MAX  
UNIT  
Analogue Output Levels  
Output Level  
0dBFS  
1.89  
1
2.1  
2.31  
Vrms  
k  
Load Impedance  
Load Capacitance  
No external RC filter  
300  
1
pF  
With filter shown in  
Error! Reference  
source not found.  
μF  
DAC Performance  
Signal to Noise Ratio  
SNR  
RL = 10kΩ  
A-weighted  
RL = 10kΩ  
Un-weighted  
RL = 10kΩ  
A-weighted  
RL = 10kΩ  
-1dBFS  
100  
106  
104  
104  
-89  
-86  
dB  
dB  
dB  
dB  
dB  
Dynamic Range  
DNR  
THD  
Total Harmonic Distortion  
RL = 10kΩ  
0dBFS  
AVDD + LINEVDD  
PSRR  
100Hz  
54  
54  
dB  
dB  
Power Supply Rejection Ratio  
1kHz  
20kHz  
50  
dB  
Channel Separation  
1kHz  
dB  
100  
20Hz to 20kHz  
dB  
95  
0
System Absolute Phase  
Channel Level Matching  
Mute Attenuation  
degrees  
dB  
0.1  
-120  
0
dB  
DC Offset at LINEVOUTL and  
LINEVOUTR  
-1  
1
mV  
Digital Logic Levels  
Input HIGH Level  
VIH  
VIL  
0.7×  
V
V
V
V
LINEVDD  
Input LOW Level  
Output HIGH Level  
Output LOW Level  
0.3×  
LINEVDD  
VOH  
VOL  
0.9×  
LINEVDD  
IOL = 1mA  
0.1×  
LINEVDD  
IOH = -1mA  
Input Capacitance  
Input Leakage  
10  
pF  
-0.9  
0.9  
μA  
TERMINOLOGY  
1. Signal-to-Noise Ratio (dB) – SNR is a measure of the difference in level between the maximum theoretical full scale output signal  
and the output with no input signal applied.  
2. Total Harmonic Distortion (dB) – THD is the level of the rms value of the sum of harmonic distortion products relative to the  
amplitude of the measured output signal.  
3. All performance measurements carried out with 20kHz low pass filter, and where noted an A-weighted filter. Failure to use such a  
filter will result in higher THD and lower SNR readings than are found in the Electrical Characteristics. The low pass filter removes  
out of band noise; although it is not audible it may affect dynamic specification values.  
4. Mute Attenuation – This is a measure of the difference in level between the full scale output signal and the output with mute  
applied.  
PD, Rev 4.1, August 2011  
w
9