US3007
if the total DI, the change from light load to full load is
14A, then the output voltage measured at the top of the
resistor divider which is also connected to the output
capacitors in this case, must be set at half of the 70 mV
or 35mV higher than the DAC voltage setting. This in-
tentional voltage level shifting during the load transient
eases the requirement for the output capacitor ESR at
the cost of load regulation. One can show that the new
ESR requirement eases up by half the total trace re-
sistance. For example, if the ESR requirement of the
output capacitors without voltage level shifting must be
7mW then after level shifting the new ESR will only need
to be 8.5mW if the trace resistance is 5mW (7+5/2=9.5).
However, one must be careful that the combined “volt-
age level shifting” and the transient response is still within
the maximum tolerance of the Intel specification. To in-
sure this, the maximum trace resistance must be less
than:
Appl icat ion Infor mat ion
An example of how to calculate the components for the
application circuit is given below.
Assuming, two set of output conditions that this regula-
tor must meet for Vcore :
a) Vo=2.8V , Io=14.2A, DVo=185mV, DIo=14.2A
b) Vo=2V , Io=14.2A, DVo=140mV, DIo=14.2A
Also, the on board 3.3V supply must be able to provide
10A load current and maintain less than ±5% total out-
put voltage variation.
The regulator design will be done such that it meets the
worst case requirement of each condition.
Output Capacitor Selection
Vcore
The first step is to select the output capacitor. This is
done primarily by selecting the maximum ESR value
that meets the transient voltage budget of the total DVo
specification. Assuming that the regulators DC initial
accuracy plus the output ripple is 2% of the output volt-
age, then the maximum ESR of the output capacitor is
calculated as :
Rs£ 2(Vspec - 0.02*Vo - DVo)/DI
Where :
Rs=Total maximum trace resistance allowed
Vspec=Intel total voltage spec
Vo=Output voltage
DVo=Output ripple voltage
DI=load current step
For example, assuming:
Vspec=±140 mV=±0.1V for 2V output
100
ESR £
= 7 mW
14.2
Vo=2V
The Sanyo MVGX series is a good choice to achieve
both the price and performance goals. The 6MV1500GX
, 1500uF, 6.3V has an ESR of less than 36 mW typ .
Selecting 6 of these capacitors in parallel has an ESR
of »6 mW which achieves our low ESR goal.
DVo=assume 10mV=0.01V
DI=14.2A
Then the Rs is calculated to be:
Rs£ 2(0.140 - 0.02*2 - 0.01)/14.2=12.6mW
However, if a resistor of this value is used, the maximum
power dissipated in the trace (or if an external resistor is
being used) must also be considered. For example if
Other type of Electrolytic capacitors from other manu-
facturers to consider are the Panasonic “FA” series or
the Nichicon “PL” series.
Rs=12.6 mW
,
the power dissipated is
(Io^2)*Rs=(14.2^2)*12.6=2.54W. This is a lot of power to
be dissipated in a system. So, if the Rs=5mW, then the
power dissipated is about 1W which is much more ac-
ceptable. If level shifting is not implemented, then the
maximum output capacitor ESR was shown previously
to be 7mW which translated to » 6 of the 1500uF,
6MV1500GX type Sanyo capacitors. With Rs=5mW, the
maximum ESR becomes 9.5mW which is equivalent to
» 4 caps. Another important consideration is that if a
trace is being used to implement the resistor, the
power dissipated by the trace increases the case
temperature of the output capacitors which could
seriously effect the life time of the output capaci-
tors.
3.3V supply
For the 3.3V supply, since there is not fast transient
requirement, 2 of the 1500uf capacitors is sufficient.
Reducing the Output Capacitors Using Voltage Level
Shifting Technique
The trace resistance or an external resistor from the output
of the switching regulator to the Slot 1 can be used to
the circuit advantage and possibly reduce the number
of output capacitors, by level shifting the DC regu-
lation point when transitioninig from light load to
full load and vice versa. To accomplish this, the out-
put of the regulator is typically set about half the DC
drop that results from light load to full load. For example,
if the total resistance from the output capacitors to the
Slot 1 and back to the GND pin of the 3007 is 5mW and
Rev. 1.8
12/8/00
4-11
UNISEM [ UNISEM ]
