欢迎访问ic37.com |
会员登录 免费注册
发布采购

TMC603 参数 Datasheet PDF下载

TMC603图片预览
型号: TMC603
PDF下载: 下载PDF文件 查看货源
内容描述: 三相电机驱动器与无刷直流电机反电势换向hallFX ™和电流感应 [Three phase motor driver with BLDC back EMF commutation hallFX™ and current sensing]
分类和应用: 驱动器电机
文件页数/大小: 41 页 / 760 K
品牌: TRINAMIC [ TRINAMIC MOTION CONTROL GMBH & CO. KG. ]
 浏览型号TMC603的Datasheet PDF文件第32页浏览型号TMC603的Datasheet PDF文件第33页浏览型号TMC603的Datasheet PDF文件第34页浏览型号TMC603的Datasheet PDF文件第35页浏览型号TMC603的Datasheet PDF文件第37页浏览型号TMC603的Datasheet PDF文件第38页浏览型号TMC603的Datasheet PDF文件第39页浏览型号TMC603的Datasheet PDF文件第40页  
TMC603 DATA SHEET (V. 1.06 / 26. Mar. 2009)  
36  
Current measurement block  
Parameter  
DC-Characteristics, Timing-Characteristics  
VVM = 24 V, VVCC = 5.0 V  
Symbol Conditions  
Min  
-4.3  
-17  
Typ  
-4.6  
Max  
-4.9  
-19  
Unit  
Amplification of voltage  
VBMX to VCURX  
for positive voltage (VBMX > 0V)  
ACURLO+ SENSE_HI = GND  
V/V  
V/V  
ACURHI+  
SENSE_HI = VCC  
-18.0  
Amplification of voltage  
VBMX to VCURX  
for negative voltage (VBMX < 0V)  
ACURLO-  
ACURHI-  
SENSE_HI = GND  
SENSE_HI = VCC  
-4.1  
-16  
-4.4  
-4.7  
-18  
V/V  
V/V  
-17.1  
Zero current level at CURX  
V0CURX  
VBMX  
VVCC/3  
-50mV  
VVCC/3  
VVCC/3  
+50mV  
V
Measurement voltage range at  
VBMX  
SENSE_HI = GND  
SENSE_HI = VCC  
-250  
-80  
300  
80  
mV  
mV  
V
VCURX output voltage swing low  
VCURX output voltage swing high  
VCURX  
VCURX  
VCURX  
0.02  
0.1  
VVCC-1.2 VVCC-0.6  
17  
V
Ripple voltage / hold step noise  
at output  
VBMX = 0V  
26  
75  
mV  
SENSE_HI = GND  
note 2)  
VBMX = 0V  
50  
mV  
µs  
SENSE_HI = VCC  
Minimum low side on time for  
current measurement  
tBLHICURX SAMPLEx = VCC  
3.5  
5.3  
7.2  
(Delay from BLx going active to  
CURx tracking amplified signal)  
Delay from SAMPLEx going  
active to CURx tracking  
amplified signal  
tSMPHICURX SAMPLEx = VCC  
tBLHICURX  
/ 2  
µs  
Delay from BLx or SAMPLEx  
going inactive to CURx hold  
tBLXLO  
dVCURX  
dVCURX  
0
µs  
V/s  
V/s  
Sample and hold drop during  
hold period  
0.001  
0.003  
1.6  
3
Auto zero drop of current  
amplifier during sampling period  
(low side on)  
Minimum initial auto zero period  
(low side off or SAMPLEx low)  
after power on  
tBLXLO0  
5
µs  
Minimum sample period after  
tBLXHIADD  
1
µs  
tBLHICURX for a 100% current step  
Output current limit at CURx  
ICURX  
Current sourcing  
0.45  
mA  
2) Note on first ICs dated before 20/2009:  
CURx outputs are sensible to ripple voltage on VCC pin and frequency below 5MHz. Ripple voltage is amplified by 1/3 * Set  
amplification, i.e. factor 1.5 with SENSE_HI low and factor 6 with SENSE_HI high. Thus, it is suggested to use 5VOUT only for  
VCC supply, if possible, if exact measurements are required.  
Copyright © 2008 TRINAMIC Motion Control GmbH & Co. KG  
 复制成功!