TS9001
ELECTRICAL CHARACTERISTICS: TS9001-1/2
VCC = +5V, VEE = 0V, VIN+ = VREF, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C. See Note 1
PARAMETER
SYMBOL CONDITIONS
MIN
TYP
MAX
UNITS
Inferred from the
PSRR test
Supply Voltage Range
VCC
TA = TMIN to TMAX
1.6
5.5
VCC = 1.6V
TA = +25°C
TA = +25°C
TA = TMIN to TMAX
0.6
0.68
1
1.30
1.60
VCC + 0.2
5
Supply Current
ICC
μA
VCC = 5V
IN+ Voltage Range
VIN+
VOS
Inferred from the output swing test
VEE - 0.2
V
mV
mV
nA
TA = +25°C
TA = TMIN to TMAX
2
Input Offset Voltage
(Note 2)
10
Input-Referred Hysteresis
Input Bias Current
VHB
(Note 3)
TA = +25°C
TA = TMIN to TMAX
4
0.15
1
2
IB
Power-Supply Rejection Ratio
PSRR
VCC = 1.6V to 5.5V, TA = TMIN to TMAX
1
mV/V
TA = +25°C
TA = TMIN to TMAX
VCC = 1.6V,
TA = +25°C
VCC = 1.6V,
200
100
300
400
TS9001-1, VCC = 5V,
ISOURCE = 5mA
Output-Voltage Swing High
Output-Voltage Swing Low
VCC - VOH
mV
mV
150
200
TS9001-1,
ISOURCE = 1mA
TA = TMIN to TMAX
TA = +25°C
TA = TMIN to TMAX
VCC = 1.6V,
TA = +25°C
VCC = 1.6V,
110
50
200
300
VCC = 5V, ISINK = 5mA
ISINK = 1mA
VOL
100
150
1
TA = TMIN to TMAX
Output Leakage Current
ILEAK
ISC
TS9001-2 only, VO = 5.5V
Sourcing, VO = VEE
0.002
60
6
90
10
12
15
25
50
μA
VCC = 5V
VCC = 1.6V
VCC = 5V
Output Short-Circuit Current
mA
Sinking, VO = VCC
VCC = 1.6V
VCC = 1.6V
VCC = 5V
High-to-Low Propagation Delay
(Note 4)
tPD-
µs
µs
VCC = 1.6V
VCC = 5V
VCC = 1.6V,
RPULLUP = 100kΩ
VCC = 5V,
TS9001-1 only
Low-to-High Propagation Delay
(Note 4)
tPD+
21
28
TS9001-2 only
RPULLUP = 100kΩ
Rise Time
Fall Time
tRISE
tFALL
TS9001-1 only, CL = 15pF
CL = 15pF
3.5
2
µs
µs
Power-Up Time
tON
1.2
ms
TA = +25°C
TA = TMIN to TMAX
1.2395
1.2332
1.252
1.2645
1.2708
Reference Voltage
VREF
V
Reference Voltage
Temperature Coefficient
Reference Output Voltage
Noise
TCVREF
en
40
ppm/°C
mVRMS
BW = 10Hz to 100kHz
BW = 10Hz to 100kHz, CREF = 1nF
0.6
0.2
Reference Line Regulation
Reference Load Regulation
∆VREF/ ∆VCC VCC = 1.6V to 5.5V
∆VREF/ ∆IOUT ∆IOUT = 10nA
0.1
mV/V
±0.2
mV/nA
Note 1: All specifications are 100% tested at TA = +25°C. Specification limits over temperature (TA = TMIN to TMAX) are guaranteed by
device characterization, not production tested.
Note 2: VOS is defined as the center of the hysteresis band at the input.
Note 3: The hysteresis-related trip points are defined by the edges of the hysteresis band and measured with respect to the center of
the hysteresis band (i.e., VOS). See Figure 2.
Note 4: The propagation delays are specified with an input overdrive (VOVERDRIVE) of 100mV and an output load capacitance of
CL = 15pF. VOVERDRIVE is defined above and is beyond the offset voltage and hysteresis of the comparator input. Reference
voltage error should also be included.
TS9001DS r1p0
Page 3
RTFDS
TOUCHSTONE [ TOUCHSTONE SEMICONDUCTOR INC ]
