TLC227x, TLC227xA
Advanced LinCMOS RAIL TO RAIL
OPERATIONAL AMPLIFIERS
SLOS190G − FEBRUARY 1997 − REVISED MAY 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
†
Supply voltage, V
DD +
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V
Supply voltage, V
DD −
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −8 V
Differential input voltage, V
ID
(see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
±
16 V
Input voltage range, V
I
(any input, see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
DD−
− 0.3 V to V
DD+
Input current, I
I
(any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
±
5 mA
Output current, I
O
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
±
50 mA
Total current into V
DD +
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
±
50 mA
Total current out of V
DD −
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
±
50 mA
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Package thermal impedance,
θ
JA
(see Notes 4 and 5): D package (8 pin) . . . . . . . . . . . . . . . . . . . . 97.1°C/W
D package (14 pin) . . . . . . . . . . . . . . . . . . . 86.2°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . 79.7°C/W
P package . . . . . . . . . . . . . . . . . . . . . . . . . . 84.6°C/W
PW package (8 pin) . . . . . . . . . . . . . . . . . . . 149°C/W
PW package (14 pin) . . . . . . . . . . . . . . . . . . 113°C/W
Package thermal impedance,
θ
JC
(see Notes 4 and 5): FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6°C/W
J package . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1°C/W
U package . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7°C/W
Operating free-air temperature range, T
A
: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I, Q suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 125°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, P or PW package . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or U package . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VDD+ and VDD −.
2. Differential voltages are at IN+ with respect to IN −. Excessive current will flow if input is brought below VDD − − 0.3 V.
3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
4. Maximum power dissipation is a function of TJ(max),
θ
JA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) − TA)/
θ
JA. Operating at the absolute maximum TJ of 150°C can affect reliability.
5. The package thermal impedance is calculated in accordance with JESD 51-7 (plastic) or MIL-STD-883 Method 1012 (ceramic).
recommended operating conditions
C SUFFIX
MIN
Supply voltage, VDD
±
Input voltage, VI
Common-mode input voltage, VIC
Operating free-air temperature, TA
±
2.2
VDD −
VDD −
0
MAX
±
8
VDD + − 1.5
VDD + − 1.5
70
I SUFFIX
MIN
±
2.2
VDD −
VDD −
−40
MAX
±
8
VDD + − 1.5
VDD + − 1.5
125
Q SUFFIX
MIN
±
2.2
VDD −
VDD −
−40
MAX
±
8
VDD + − 1.5
VDD + − 1.5
125
M SUFFIX
MIN
±
2.2
VDD −
VDD −
−55
MAX
±
8
VDD + − 1.5
VDD + − 1.5
125
UNIT
V
V
V
°C
POST OFFICE BOX 655303
•
DALLAS, TEXAS 75265
5
TI [ TEXAS INSTRUMENTS ]
