THS4511
www.ti.com
SLOS471–SEPTEMBER 2005
Table 5. THS4511RGT EVM Bill of Materials
SMD
SIZE
REFERENCE
DESIGNATOR
PCB
QTY
MANUFACTURER'S
PART NUMBER(1)
ITEM
DESCRIPTION
1
2
CAP, 10.0 µF, Ceramic, X5R, 6.3V
CAP, 0.1 µF, Ceramic, X5R, 10V
CAP, 0.22 µF, Ceramic, X5R, 6.3V
OPEN
0805 C3, C5
2
4
1
6
2
1
(AVX) 08056D106KAT2A
(AVX) 0402ZD104KAT2A
(AVX) 04026D224KAT2A
0402 C11, C12, C13, C14
0402 C15
3
4
0402 C1, C2, C7, C8, C9, C10
0402 R9, R10
0402 R12
5
OPEN
6
Resistor, 49.9 Ω, 1/16W, 1%
Resistor, 56.2 Ω, 1/16W, 1%
Resistor, 69.8 Ω, 1/16W, 1%
Resistor, 86.6 Ω, 1/16W, 1%
Resistor, 340 Ω, 1/16W, 1%
Resistor, 348 Ω, 1/16W, 1%
Resistor, 0 Ω, 5%
(KOA) RK73H1ETTP49R9F
(KOA) RK73H1ETTP56R2F
(KOA) RK73H1ETTP69R8F
(KOA) RK73H1ETTP86R6F
(KOA) RK73H1ETTP3400F
(KOA) RK73H1ETTP3480F
(KOA) RK73Z2ATTD
7
0402 R1, R2
0402 R11
8
3
2
2
2
2
1
2
9
0402 R7, R8
0402 R3, R4
0402 R5, R6
0805 C4, C6
T1
10
11
12
13
Transformer, RF
(MINI-CIRCUITS) ADT1-1WT
Jack, banana receptance, 0.25" diameter
hole
14
J5, J6
(HH SMITH) 101
15
16
17
18
19
20
21
OPEN
J1, J7, J8
J2, J3
3
2
3
1
4
4
1
Connector, edge, SMA PCB Jack
Test point, Red
(JOHNSON) 142-0701-801
(KEYSTONE) 5000
(TI) THS4511RGT
TP1, TP2, TP3
U1
IC, THS4511
Standoff, 4-40 HEX, 0.625" length
SCREW, PHILLIPS, 4-40, 0.250"
Printed circuit board
(KEYSTONE) 1808
SHR-0440-016-SN
(TI) EDGE# 6475513
(1) The manufacturer's part numbers were used for tesr purposes only.
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the input and output voltage ranges as specified in the table provided
below.
Input Range, VS+ to VS-
Input Range, VI
3.0 V to 6.0 V
3.0 V to 6.0 V NOT TO EXCEED VS+ or VS-
3.0 V to 6.0 V NOT TO EXCEED VS+ or VS-
Output Range, VO
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If
there are questions concerning the input range, please contact a TI field representative prior to connecting the
input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible
permanent damage to the EVM. Please consult the product data sheet or EVM user's guide (if user's guide is
available) prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than 30°C. The EVM is
designed to operate properly with certain components above 50°C as long as the input and output ranges are
maintained. These components include but are not limited to linear regulators, switching transistors, pass
transistors, and current sense resistors. These types of devices can be identified using the EVM schematic
located in the material provided. When placing measurement probes near these devices during operation, please
be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265
22
TI [ TEXAS INSTRUMENTS ]
