LM4041-N, LM4041-N-Q1
SNOS641F –OCTOBER 1999–REVISED JULY 2013
www.ti.com
LM4041-N/LM4041-N-Q1 1.2 Electrical Characteristics (Extended Temperature Range)
Boldface limits apply for TA = TJ = TMINto TMAX; all other limits TA = TJ = 25°C. The grades C, D and E designate initial
Reverse Breakdown Voltage tolerance of ±0.5%, ±1.0% and ±2.0% respectively.
Symbol
Parameter
Conditions
Typical(1)
LM4041CEM3
LM4041DEM3
LM4041EEM3
Units
LM4041QCEM3 LM4041QDEM3 LM4041QEEM3
(Limit)
Limits(2)
Limits(2)
Limits(2)
VR
Reverse Breakdown
Voltage
IR = 100 μA
1.225
V
Reverse Breakdown
Voltage Error(3)
IR = 100 μA
±6
±12
±25
mV (max)
mV (max)
μA
±18.4
±31
±43
IRMIN
Minimum Operating
Current
45
60
65
65
μA (max)
μA (max)
ppm/°C
68
73
73
ΔVR/ΔT VR Temperature
IR= 10 mA
IR = 1 mA
±20
±15
Coefficient(3)
ppm/°C
(max)
±100
±150
±150
IR = 100 μA
±15
0.7
ppm/°C
mV
ΔVR/ΔIR Reverse Breakdown
Change with
IRMIN ≤ IR ≤ 1.0 mA
1.5
2.0
2.0
mV (max)
mV (max)
mV
Current(4)
2.0
2.5
2.5
1 mA ≤ IR ≤ 12 mA
2.5
0.5
6.0
8.0
8.0
mV (max)
mV (max)
Ω
8.0
10.0
10.0
ZR
eN
Reverse Dynamic
Impedance
IR = 1 mA, f = 120
Hz,
IAC= 0.1 IR
Ω (max)
1.5
2.0
2.0
Noise Voltage
IR = 100 μA
10 Hz ≤ f ≤ 10 kHz
20
μVrms
ppm
%
ΔVR
Long Term Stability
(Non-Cumulative)
t = 1000 hrs
T = 25°C ±0.1°C
IR = 100 μA
120
0.08
VHYST
Thermal Hysteresis(5) ΔT = −40°C to
+125°C
(1) Typicals are at TJ = 25°C and represent most likely parametric norm.
(2) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(3) The boldface (over-temperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse
Breakdown Voltage Tolerance ±[(ΔVR↱ΔT)(max ΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum
difference in temperature from the reference point of 25 °C to T MAX or TMIN, and VR is the reverse breakdown voltage. The total over-
temperature tolerance for the different grades in the industrial temperature range where maxΔT=65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total over-temperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown
below:
B-grade: ±1.2% = ±0.2% ±100 ppm/°C × 100°C
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±4.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade LM4041-N 1.2 has an over-temperature Reverse Breakdown Voltage tolerance of ±1.2V × 0.75%
= ±9.2 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Ouput changes due to die temperature change
must be taken into account separately.-
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature +125°C.
6
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM4041-N, LM4041-N-Q1
TI [ TEXAS INSTRUMENTS ]
