欢迎访问ic37.com |
会员登录 免费注册
发布采购

CC2510F16 参数 Datasheet PDF下载

CC2510F16图片预览
型号: CC2510F16
PDF下载: 下载PDF文件 查看货源
内容描述: 低功耗的SoC (系统级芯片)与MCU,存储器, 2.4 GHz射频收发器和USB控制器 [Low-Power SoC (System-on-Chip) with MCU, Memory, 2.4 GHz RF Transceiver, and USB Controller]
分类和应用: 存储射频控制器
文件页数/大小: 244 页 / 2582 K
品牌: TI [ TEXAS INSTRUMENTS ]
 浏览型号CC2510F16的Datasheet PDF文件第179页浏览型号CC2510F16的Datasheet PDF文件第180页浏览型号CC2510F16的Datasheet PDF文件第181页浏览型号CC2510F16的Datasheet PDF文件第182页浏览型号CC2510F16的Datasheet PDF文件第184页浏览型号CC2510F16的Datasheet PDF文件第185页浏览型号CC2510F16的Datasheet PDF文件第186页浏览型号CC2510F16的Datasheet PDF文件第187页  
CC2510Fx / CC2511Fx  
13 Radio  
RADIO CONTROL  
ADC  
LNA  
ADC  
RF_P  
RF_N  
FREQ  
SYNTH  
0
90  
PA  
Figure 47: CC2510Fx/CC2511Fx Radio Module  
A simplified block diagram of the radio module  
The frequency synthesizer includes  
a
completely on-chip LC VCO and a 90 degrees  
phase shifter for generating the I and Q LO  
signals to the down-conversion mixers in  
receive mode.  
in the CC2510Fx/CC2511Fx is shown in Figure 47.  
CC2510Fx/CC2511Fx features a low-IF receiver.  
The received RF signal is amplified by the low-  
noise amplifier (LNA) and down-converted in  
quadrature (I and Q) to the intermediate  
frequency (IF). At IF, the I/Q signals are  
digitized by the ADCs. Automatic gain control  
(AGC), fine channel filtering, demodulation  
bit/packet synchronization are performed  
digitally.  
The high speed crystal oscillator generates the  
reference frequency for the synthesizer, as  
well as clocks for the ADC and the digital part.  
An SFR interface is used for data buffer  
access from the CPU. Configuration and status  
registers are accessed through registers  
mapped to XDATA memory.  
The transmitter part of CC2510Fx/CC2511Fx is  
based on direct synthesis of the RF frequency.  
The digital baseband includes support for  
channel configuration, packet handling, and  
data buffering.  
Note: In this section of the document, fRef is used to denote  
the reference frequency for the synthesizer.  
fXOSC  
For CC2510Fx and for CC2511Fx,  
fref = fXOSC  
fref  
=
2
13.1 Command Strobes  
The CPU uses a set of command strobes to  
control operation of the radio.  
Note: An SIDLE strobe will clear all pending  
command strobes until IDLE state is  
reached. This means that if for example an  
SIDLE strobe is issued while the radio is in  
RX state, any other command strobes  
issued before the radio reached IDLE state  
will be ignored.  
Command strobes may be viewed as single  
byte instructions which each start an internal  
sequence in the radio. These command  
strobes are used to enable the frequency  
synthesizer, enable receive mode, enable  
transmit mode, etc. (see Figure 48).  
The 6 command strobes are listed in Table 61  
on Page 185.  
SWRS055F  
Page 183 of 241  
 
 
 复制成功!