Sidac
Data Sheets
IT(RMS)
(7) (8)
VDRM
VBO
(1)
IDRM
IBO
(2)
IH
(3) (4)
Part No.
(10)
Type
TO-92
DO-15X
DO-214
TO-202
Amps
MAX
1
1
1
1
1
1
1
1
1
1
1
Volts
MIN
±70
±90
±90
±90
±90
±90
±90
±180
±180
±190
±200
±200
Volts
µAmps
MAX
5
5
5
5
5
5
5
5
5
5
5
µAmps
MAX
10
10
10
10
10
10
10
10
10
10
10
mAmps
See “Package Dimensions” section for variations. (9)
K0900E70
MIN
79
95
MAX
97
TYP
60
60
60
60
60
60
60
60
60
60
60
60
MAX
150
150
150
150
150
150
150
150
150
150
150
150
K0900G
K1050G
K1100G
K1200G
K1300G
K1400G
K1500G
K2000G
K2200G
K2400G
K2500G
K0900S
K1050E70
K1100E70
K1200E70
K1300E70
K1400E70
K1500E70
K2000E70
K2200E70
K2400E70
K2500E70
K1050S
K1100S
K1200S
K1300S
K1400S
K1500S
K2000S
K2200S
K2400S
K2500S
113
118
125
138
146
170
215
230
250
280
330
104
110
120
130
140
190
205
220
240
270
K2000F1
K2200F1
K2400F1
K2500F1
K3000F1
1
5
10
Specific Test Conditions
di/dt — Critical rate-of-rise of on-state current
Electrical Specification Notes
(1) See Figure E9.5 for VBO change versus junction temperature.
dv/dt — Critical rate-of-rise of off-state voltage at rated VDRM
;
(2) See Figure E9.6 for IBO versus junction temperature.
(3) See Figure E9.2 for IH versus case temperature.
(4) See Figure E9.13 for test circuit.
TJ ≤ 100 °C
I
I
I
I
I
BO — Breakover current 50/60 Hz sine wave
DRM — Repetitive peak off-state current 50/60 Hz sine wave; V = VDRM
H — Dynamic holding current 50/60 Hz sine wave; R = 100 Ω
(5) See Figure E9.1 for more than one full cycle rating.
(6)
T
C ≤ 90 °C for TO-92 Sidac
T
C ≤ 105 °C for TO-202 Sidacs
T(RMS) — On-state RMS current T ≤ 125 °C 50/60 Hz sine wave
J
TL ≤ 100 °C for DO-15X
TL ≤ 90 °C for DO-214
TSM — Peak one-cycle surge current 50/60 Hz sine wave (non-
repetitive)
(V
– V )
BO
S
)
(7) See Figure E9.14 for clarification of sidac operation.
RS — Switching resistance R = ------------------------------- 50/60 Hz sine wave
S
(I – I
(8) For best sidac operation, the load impedance should be near or
BO
S
less than switching resistance.
VBO — Breakover voltage 50/60 Hz sine wave
VDRM — Repetitive peak off-state voltage
VTM — Peak on-state voltage; IT = 1 A
(9) See package outlines for lead form configurations. When ordering
special lead forming, add type number as suffix to part number.
(10) Do not use electrically connected mounting tab or center lead.
+I
General Notes
I
T
•
All measurements are made at 60 Hz with a resistive load at an
ambient temperature of +25 °C unless otherwise specified.
I
R
H
S
•
•
Storage temperature range (TS) is -65 °C to +150 °C.
I
The case (TC) or lead (TL) temperature is measured as shown on
the dimensional outline drawings in the “Package Dimensions” sec-
tion of this catalog.
S
I
BO
I
DRM
-V
+V
•
•
Junction temperature range (TJ) is -40 °C to +125 °C.
Lead solder temperature is a maximum of +230 °C for 10-second
maximum; ≥1/16" (1.59 mm) from case.
V
BO
V
V
T
S
(V - V )
BO
S
)
R
=
V
S
DRM
(I - I
S
BO
-I
V-I Characteristics
http://www.teccor.com
+1 972-580-7777
E9 - 2
©2002 Teccor Electronics
Thyristor Product Catalog
TECCOR [ TECCOR ELECTRONICS ]
