1 Mbit SPI Serial Flash
SST25VF010
Data Sheet
Block Protection (BP1, BP0)
Status Register
The Block-Protection (BP1, BP0) bits define the size of the
memory area, as defined in Table 4, to be software pro-
tected against any memory Write (Program or Erase)
operations. The Write-Status-Register (WRSR) instruction
is used to program the BP1 and BP0 bits as long as WP#
is high or the Block-Protect-Lock (BPL) bit is 0. Chip-Erase
can only be executed if Block-Protection bits are both 0.
After power-up, BP1 and BP0 are set to 1.
The software status register provides status on whether the
flash memory array is available for any Read or Write oper-
ation, whether the device is Write enabled, and the state of
the memory Write protection. During an internal Erase or
Program operation, the status register may be read only to
determine the completion of an operation in progress.
Table 5 describes the function of each bit in the software
status register.
Block Protection Lock-Down (BPL)
Busy
WP# pin driven low (VIL), enables the Block-Protection-
Lock-Down (BPL) bit. When BPL is set to 1, it prevents any
further alteration of the BPL, BP1, and BP0 bits. When the
WP# pin is driven high (VIH), the BPL bit has no effect and
its value is “Don’t Care”. After power-up, the BPL bit is
reset to 0.
The Busy bit determines whether there is an internal Erase
or Program operation in progress. A “1” for the Busy bit indi-
cates the device is busy with an operation in progress. A “0”
indicates the device is ready for the next valid operation.
Write Enable Latch (WEL)
The Write-Enable-Latch bit indicates the status of the inter-
nal memory Write Enable Latch. If the Write-Enable-Latch
bit is set to “1”, it indicates the device is Write enabled. If the
bit is set to “0” (reset), it indicates the device is not Write
enabled and does not accept any memory Write (Program/
Erase) commands. The Write-Enable-Latch bit is automati-
cally reset under the following conditions:
TABLE 4: SOFTWARE STATUS REGISTER
1
BLOCK PROTECTION
Status
Register Bit
Protected
Protection Level
0
BP1 BP0
Memory Area
None
0
0
1
1
0
1
0
1
1 (1/4 Memory Array)
2 (1/2 Memory Array)
3 (Full Memory Array)
018000H-01FFFFH
010000H-01FFFFH
•
•
•
•
Power-up
Write-Disable (WRDI) instruction completion
Byte-Program instruction completion
000000H-01FFFFH
T4.0 1233
Auto Address Increment (AAI) programming
reached its highest memory address
1. Default at power-up for BP1 and BP0 is ‘11’.
Auto Address Increment (AAI)
•
•
•
Sector-Erase instruction completion
Block-Erase instruction completion
Chip-Erase instruction completion
The Auto Address Increment Programming-Status bit pro-
vides status on whether the device is in AAI programming
mode or Byte-Program mode. The default at power up is
Byte-Program mode.
TABLE 5: SOFTWARE STATUS REGISTER
Bit Name Function
Default at Power-up
Read/Write
0
BUSY 1 = Internal Write operation is in progress
0 = No internal Write operation is in progress
0
R
1
WEL
1 = Device is memory Write enabled
0
R
0 = Device is not memory Write enabled
2
3
BP0
BP1
Indicate current level of block write protection (See Table 4)
Indicate current level of block write protection (See Table 4)
Reserved for future use
1
1
0
0
R/W
R/W
N/A
R
4:5 RES
6
AAI
Auto Address Increment Programming status
1 = AAI programming mode
0 = Byte-Program mode
7
BPL
1 = BP1, BP0 are read-only bits
0 = BP1, BP0 are read/writable
0
R/W
T5.0 1233
©2005 Silicon Storage Technology, Inc.
S71233-04-000
1/05
6
SST [ SILICON STORAGE TECHNOLOGY, INC ]
