欢迎访问ic37.com |
会员登录 免费注册
发布采购

S29AL016M10BFI020 参数 Datasheet PDF下载

S29AL016M10BFI020图片预览
型号: S29AL016M10BFI020
PDF下载: 下载PDF文件 查看货源
内容描述: 16兆位( 2M ×8位/ IMX 16位), 3.0伏只引导扇区闪存 [16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY]
分类和应用: 闪存内存集成电路
文件页数/大小: 59 页 / 2056 K
品牌: SPANSION [ SPANSION ]
 浏览型号S29AL016M10BFI020的Datasheet PDF文件第11页浏览型号S29AL016M10BFI020的Datasheet PDF文件第12页浏览型号S29AL016M10BFI020的Datasheet PDF文件第13页浏览型号S29AL016M10BFI020的Datasheet PDF文件第14页浏览型号S29AL016M10BFI020的Datasheet PDF文件第16页浏览型号S29AL016M10BFI020的Datasheet PDF文件第17页浏览型号S29AL016M10BFI020的Datasheet PDF文件第18页浏览型号S29AL016M10BFI020的Datasheet PDF文件第19页  
to be programmed with its corresponding programming algorithm. However, the  
autoselect codes can also be accessed in-system through the command register.  
When using programming equipment, the autoselect mode requires V (11.5 V  
ID  
to 12.5 V) on address pin A9. Address pins A6, A1, and A0 must be as shown in  
Table 4. In addition, when verifying sector protection, the sector address must  
appear on the appropriate highest order address bits (see Tables 2 and 3). Table  
4 shows the remaining address bits that are don’t care. When all necessary bits  
have been set as required, the programming equipment may then read the cor-  
responding identifier code on DQ7-DQ0.  
To access the autoselect codes in-system, the host system can issue the autose-  
lect command via the command register, as shown in Tables 1011. This method  
does not require V . See “Command Definitions” for details on using the autose-  
ID  
lect mode.  
Table 4. Autoselect Codes (High Voltage Method)  
A19 A11  
to to  
Mode CE# OE# WE# A12 A10 A9  
A8  
to  
A7  
A5  
to  
DQ8  
to  
DQ7  
to  
DQ0  
Description  
A6  
A2 A1 A0 DQ15  
Manufacturer ID  
(Spansion Products)  
L
L
L
L
H
H
X
X
VID  
X
X
L
X
X
L
L
X
01h  
C4h  
Device ID:  
S29AL016M  
(Model 01)  
Word  
Byte  
Word  
22h  
X
X
VID  
L
L
L
H
L
L
L
L
H
H
X
C4h  
49h  
(Top Boot Block)  
Device ID:  
S29AL016M  
(Model 02)  
(Bottom Boot  
Block)  
22h  
X
X
VID  
X
X
L
H
Byte  
L
L
L
L
H
H
X
49h  
X
X
01h (protected)  
Sector Protection  
Verification  
SA  
X
X
X
VID  
X
X
L
X
X
H
L
L
00h  
(unprotected)  
83 (factory  
locked  
03h (not  
SecSi Sector Indicator Bit  
(DQ7)  
L
L
H
VID  
H
H
X
factory locked)  
L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care.  
Note: The autoselect codes may also be accessed in-system via command sequences. See Tables 1011.  
Sector Protection/Unprotection  
The hardware sector protection feature disables both program and erase opera-  
tions in any sector. The hardware sector unprotection feature re-enables both  
program and erase operations in previously protected sectors.  
The device is normally shipped with all sectors unprotected. However, the Ex-  
pressFlash™ Service offers the option of programming and protecting sectors at  
the factory prior to shipping the device. Contact a sales office or representative  
for details.  
It is possible to determine whether a sector is protected or unprotected. See “Au-  
toselect Mode” for details.  
April 21, 2004 S29AL016M_00A4  
S29AL016M  
16