欢迎访问ic37.com |
会员登录 免费注册
发布采购

USB2241 参数 Datasheet PDF下载

USB2241图片预览
型号: USB2241
PDF下载: 下载PDF文件 查看货源
内容描述: 超快速USB 2.0多格式闪存介质控制器 [Ultra Fast USB 2.0 Multi-Format Flash Media Controller]
分类和应用: 闪存控制器
文件页数/大小: 28 页 / 688 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号USB2241的Datasheet PDF文件第11页浏览型号USB2241的Datasheet PDF文件第12页浏览型号USB2241的Datasheet PDF文件第13页浏览型号USB2241的Datasheet PDF文件第14页浏览型号USB2241的Datasheet PDF文件第16页浏览型号USB2241的Datasheet PDF文件第17页浏览型号USB2241的Datasheet PDF文件第18页浏览型号USB2241的Datasheet PDF文件第19页  
Ultra Fast USB 2.0 Multi-Format Flash Media Controller  
Datasheet  
Table 5.1 USB2240/USB2241 36-Pin QFN Pin Descriptions (continued)  
36-PIN  
QFN  
BUFFER  
TYPE  
NAME  
MS Card  
SYMBOL  
DESCRIPTION  
GPIO12  
(MS_INS)  
24  
IPU  
This is a GPIO designated as the Memory StickTM  
card detection pin.  
Insertion GPIO  
SECURE DIGITAL INTERFACE  
SD Data  
SD_D[7:0]  
7
I/O12PU  
The bi-directional signals should have weak pull-up  
resistors. The register can be controlled by:  
SD_MMC_INTF_EN bit of SDC_MODE_CTL  
8
10  
20  
23  
25  
4
5
SD Clock  
SD_CLK  
SD_CMD  
9
O12  
This is an output clock signal to SD/MMC device.  
The clock frequency is software configurable.  
SD Command  
11  
I/O12PU  
This is a bi-directional signal that connects to the  
CMD signal of SD/MMC device. The bi-directional  
signal should have an internal weak pull-up resistor.  
The pull-up register can be controlled by:  
SD_MMC_INTF_EN bit of SDC_MODE CTL  
SD Write  
GPIO6  
30  
26  
I/O12  
I/O12  
This is a GPIO designated as the Secure Digital  
card mechanical write detect pin.  
Protected GPIO (SD_nWP)  
SD Card Detect  
GPIO  
GPIO15  
(SD_nCD)  
This is a GPIO designated as the Secure Digital  
card detection pin.  
USB INTERFACE  
USB Bus Data  
USB+  
USB-  
2
3
I/O-U  
I-R  
These pins connect to the USB bus data signals.  
USB  
Transceiver  
Bias  
RBIAS  
35  
33  
32  
A 12.0k , 1.0% resistor is attached from VSSA to  
this pin in order to set the transceiver's internal bias  
currents.  
24MHz Crystal  
or external  
clock input  
XTAL1  
(CLKIN)  
ICLKx  
This pin can be connected to one terminal of the  
crystal or can be connected to an external 24 clock  
when a crystal is not used.  
24MHz Crystal  
XTAL2  
OCLKx  
This is the other terminal of the crystal, or left open  
when an external clock source is used to drive  
XTAL1/CLKIN. It may not be used to drive any  
external circuitry other than the crystal circuit.  
MISC  
General  
Purpose I/O  
GPIO1  
(LED1)  
1
I/O12  
This pin may be used either as input, edge sensitive  
interrupt input, or output.  
In addition, as an output, the GPIO1 can be used  
output controlled by the LED1_GPIO1 register.  
SMSC USB2240/USB2241  
Revision 2.6 (05-08-08)  
DATA1S5HEET  
 复制成功!