欢迎访问ic37.com |
会员登录 免费注册
发布采购

LAN91C96I-MS 参数 Datasheet PDF下载

LAN91C96I-MS图片预览
型号: LAN91C96I-MS
PDF下载: 下载PDF文件 查看货源
内容描述: 非PCI单芯片全双对象以太网控制器 [NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER]
分类和应用: 控制器PC以太网以太网:16GBASE-T
文件页数/大小: 110 页 / 654 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号LAN91C96I-MS的Datasheet PDF文件第12页浏览型号LAN91C96I-MS的Datasheet PDF文件第13页浏览型号LAN91C96I-MS的Datasheet PDF文件第14页浏览型号LAN91C96I-MS的Datasheet PDF文件第15页浏览型号LAN91C96I-MS的Datasheet PDF文件第17页浏览型号LAN91C96I-MS的Datasheet PDF文件第18页浏览型号LAN91C96I-MS的Datasheet PDF文件第19页浏览型号LAN91C96I-MS的Datasheet PDF文件第20页  
Non-PCI Single-Chip Full Duplex Ethernet Controller  
PIN NO.  
TQFP  
QFP  
PIN NAME  
INTR3  
TYPE  
O24  
DESCRIPTION  
21  
23  
Local Bus - Outputs. Active high interrupt signals. The  
interrupt line selection is determined by the value of INT  
SEL1-0 bits in the Configuration Register. These interrupts  
are tri-stated when not selected.  
23  
25  
nIOCS16/  
nIOIS16  
OD24  
Local Bus - Active low output asserted in 16 bit mode when  
AEN is low and A4-A15 decode to the LAN91C96I address  
programmed into the high byte of the Base Address  
Register.  
49  
50  
51  
5
51  
52  
53  
7
nIORD/  
xDS  
IS with  
pullup  
Local Bus, - Input. Active low read strobe used to access the  
LAN91C96I IO space.  
**  
nIOWR/  
R/nW  
IS with  
Local Bus - Input. Active low write strobe used to access the  
LAN91C96I IO space.  
pullup  
**  
nMEMR/  
nOE  
IS with  
Local Bus - Active low signal used by the host processor to  
read from the external ROM.  
pullup  
**  
O4  
EESK  
Output. 4usec clock used to shift data in and out of a serial  
EEPROM.  
4
2
6
4
EECS  
EEDO/  
SDOUT  
EEDI  
O4  
O4  
Output. Serial EEPROM chip select.  
Output. Connected to the DI input of the serial EEPROM.  
3
5
I with  
pull-  
Input. Connected to the DO output of the serial EEPROM.  
down  
**  
96,97  
99  
98,99  
1
IOS0-1  
IOS2  
I with  
Input. External switches can be connected to these lines to  
select between predefined EEPROM configurations. The  
values of these pins are readable.  
Input. External switches can be connected to these lines to  
select between predefined EEPROM configurations. The  
values of these pins are readable.  
pullup  
I with  
pullup  
**  
70  
67  
72  
69  
nTXLED/  
nTXEN  
OD16  
INTERNAL ENDEC - Transmit LED output.  
O162  
OD16  
EXTERNAL ENDEC - Active low Transmit Enable output.  
nBSELED/  
RXD  
INTERNAL ENDEC - Board Select LED activated by  
accesses to I/O space (nIORD or nIOWR active with AEN  
low and valid address decode for Local Bus). The pulse is  
stretched beyond the access duration to make the LED  
visible.  
I with  
EXTERNAL ENDEC - NRZ receive data input.  
pullup  
69  
68  
71  
70  
nRXLED/  
RXCLK  
OD16  
INTERNAL ENDEC - Receive LED output.  
I with  
EXTERNAL ENDEC - Receive clock input.  
INTERNAL ENDEC - Link LED output.  
pullup  
nLNKLED/  
TXD  
OD16  
O162  
EXTERNAL ENDEC - Transmit Data output.  
Rev. 11/18/2004  
Page 16  
SMSC DS – LAN91C96I  
DATASHEET