欢迎访问ic37.com |
会员登录 免费注册
发布采购

LAN8710AI 参数 Datasheet PDF下载

LAN8710AI图片预览
型号: LAN8710AI
PDF下载: 下载PDF文件 查看货源
内容描述: 小尺寸MII / RMII 10/100以太网收发器, HP Auto-MDIX的和flexPWR技术 [Small Footprint MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX and flexPWR Technology]
分类和应用: 以太网局域网(LAN)标准
文件页数/大小: 82 页 / 1172 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号LAN8710AI的Datasheet PDF文件第33页浏览型号LAN8710AI的Datasheet PDF文件第34页浏览型号LAN8710AI的Datasheet PDF文件第35页浏览型号LAN8710AI的Datasheet PDF文件第36页浏览型号LAN8710AI的Datasheet PDF文件第38页浏览型号LAN8710AI的Datasheet PDF文件第39页浏览型号LAN8710AI的Datasheet PDF文件第40页浏览型号LAN8710AI的Datasheet PDF文件第41页  
®
Small Footprint MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX and flexPWR Technology  
Datasheet  
Table 3.6 MODE[2:0] Bus  
DEFAULT REGISTER BIT VALUES  
MODE[2:0]  
MODE DEFINITIONS  
REGISTER 0  
[13,12,10,8]  
REGISTER 4  
[8,7,6,5]  
000  
001  
010  
10Base-T Half Duplex. Auto-negotiation disabled.  
10Base-T Full Duplex. Auto-negotiation disabled.  
0000  
0001  
1000  
N/A  
N/A  
N/A  
100Base-TX Half Duplex. Auto-negotiation  
disabled.  
CRS is active during Transmit & Receive.  
011  
100  
100Base-TX Full Duplex. Auto-negotiation disabled.  
CRS is active during Receive.  
1001  
1100  
N/A  
100Base-TX Half Duplex is advertised. Auto-  
negotiation enabled.  
CRS is active during Transmit & Receive.  
0100  
101  
110  
Repeater mode. Auto-negotiation enabled.  
100Base-TX Half Duplex is advertised.  
CRS is active during Receive.  
1100  
N/A  
0100  
N/A  
Power Down mode. In this mode the transceiver will  
wake-up in Power-Down mode. The transceiver  
cannot be used when the MODE[2:0] bits are set to  
this mode. To exit this mode, the MODE bits in  
Register 18.7:5(see Section 4.2.9, "Special Modes  
Register," on page 60) must be configured to some  
other value and a soft reset must be issued.  
111  
All capable. Auto-negotiation enabled.  
X10X  
1111  
The MODE[2:0] hardware configuration pins are multiplexed with other signals as shown in Table 3.7.  
Table 3.7 Pin Names for Mode Bits  
MODE BIT  
PIN NAME  
MODE[0]  
MODE[1]  
MODE[2]  
RXD0/MODE0  
RXD1/MODE1  
COL/CRS_DV/MODE2  
3.7.3  
RMIISEL: MII/RMII Mode Configuration  
MII or RMII mode selection is latched on the rising edge of the internal reset (nRST) based on the  
strapping of the RMIISEL configuration strap. The default mode is MII (via the internal pull-down  
resistor). To select RMII mode, pull the RMIISEL configuration strap high with an external resistor to  
VDDIO.  
When the nRST pin is deasserted, the MIIMODE bit of the Special Modes Register is loaded according  
to the RMIISEL configuration strap. The mode is reflected in the MIIMODE bit of the Special Modes  
Register.  
Refer to Section 3.4, "MAC Interface," on page 30 for additional information on MII and RMII modes.  
SMSC LAN8710A/LAN8710Ai  
37  
Revision 1.4 (08-23-12)  
DATASHEET