欢迎访问ic37.com |
会员登录 免费注册
发布采购

EMC1182-1-AIA-TR 参数 Datasheet PDF下载

EMC1182-1-AIA-TR图片预览
型号: EMC1182-1-AIA-TR
PDF下载: 下载PDF文件 查看货源
内容描述: 双通道1C温度传感器,带有beta补偿和1.8V的SMBus通信 [Dual Channel 1C Temperature Sensor with Beta Compensation and 1.8V SMBus Communications]
分类和应用: 传感器温度传感器通信
文件页数/大小: 48 页 / 565 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号EMC1182-1-AIA-TR的Datasheet PDF文件第25页浏览型号EMC1182-1-AIA-TR的Datasheet PDF文件第26页浏览型号EMC1182-1-AIA-TR的Datasheet PDF文件第27页浏览型号EMC1182-1-AIA-TR的Datasheet PDF文件第28页浏览型号EMC1182-1-AIA-TR的Datasheet PDF文件第30页浏览型号EMC1182-1-AIA-TR的Datasheet PDF文件第31页浏览型号EMC1182-1-AIA-TR的Datasheet PDF文件第32页浏览型号EMC1182-1-AIA-TR的Datasheet PDF文件第33页  
Dual Channel 1°C Temperature Sensor with Beta Compensation and 1.8V SMBus Communications  
Datasheet  
Bit 7 - MASK_ALL - Masks the ALERT / THERM2 pin from asserting.  
‘0’ - (default) - The ALERT / THERM2 pin is not masked. If any of the appropriate status bits are  
set the ALERT / THERM2 pin will be asserted.  
‘1’ - The ALERT/ THERM2 pin is masked. It will not be asserted for any interrupt condition unless  
it is configured in comparator mode. The Status Registers will be updated normally.  
Bit 6 - RUN / STOP - Controls Active/Standby modes.  
‘0’ (default) - The device is in Active mode and converting on all channels.  
‘1’ - The device is in Standby mode and not converting.  
Bit 5 - ALERT/THERM2 - Controls the operation of the ALERT / THERM2 pin.  
‘0’ (default) - The ALERT / THERM2 acts as an Alert pin and has interrupt behavior as described  
in Section 5.5.1.  
‘1’ - The ALERT / THERM2 acts as a THERM pin and has comparator behavior as described in  
Section 5.5.2. In this mode the MASK_ALL bit is ignored.  
Bit 4 - RECD - Disables the Resistance Error Correction (REC) for the External Diode.  
‘0’ (default) - REC is enabled for the External Diode.  
‘1’ - REC is disabled for the External Diode.  
Bit 2 - RANGE - Configures the measurement range and data format of the temperature channels.  
‘0’ (default) - The temperature measurement range is 0°C to +127.875°C and the data format is  
binary.  
‘1’ -The temperature measurement range is -64°C to +191.875°C and the data format is offset  
binary (see Table 5.2).  
Bit 1 - DAVG_DIS - Disables the dynamic averaging feature on all temperature channels.  
‘0’ (default) - The dynamic averaging feature is enabled. All temperature channels will be converted  
with an averaging factor that is based on the conversion rate as shown in Table 6.6.  
‘1’ - The dynamic averaging feature is disabled. All temperature channels will be converted with a  
maximum averaging factor of 1x (equivalent to 11-bit conversion). For higher conversion rates, this  
averaging factor will be reduced as shown in Table 6.6.  
6.5  
Conversion Rate Register 04h / 0Ah  
Table 6.5 Conversion Rate Register  
ADDR  
R/W  
REGISTER  
B7  
B6  
B5  
B4  
B3  
B2  
B1  
B0  
DEFAULT  
04h  
0Ah  
Conversion  
Rate  
06h  
(4/sec)  
R/W  
-
-
-
-
CONV[3:0]  
The Conversion Rate Register controls how often the temperature measurement channels are updated  
and compared against the limits. This register is fully accessible at either address.  
Bits 3-0 - CONV[3:0] - Determines the conversion rate as shown in Table 6.6.  
SMSC EMC1182  
29  
Revision 1.0 (07-11-13)  
DATASHEET