BM28723AMUV
Absolute Maximum Ratings (Ta=25°C)
Parameter
Supply Voltage
Symbol
VCCMAX
VDVDDMAX
Limit
30
4.5
Unit
V
V
Conditions
Pin 17, 24(Note 1) (Note 2)
Pin 10(Note 1)
-0.3 to
Input Voltage 1
Pin Voltage 1
Pin Voltage 2
VIN1
VPIN1
VPIN2
V
V
V
Pin 1 to 5, 9, 11, 29 to 32(Note 1)
Pin 27(Note 1)
VDVDD+0.3(Note 2)
-0.3 to +7.0
-0.3 to
Pin 16, 20, 21, 25(Note 1) (Note 4)
+VCCMAX
-0.3 to VOUT1P+7
-0.3 to VOUT1N+7
-0.3 to VOUT2P+7
-0.3 to VOUT2N+7
-0.3 to +2.1
-0.3 to +7.0
-25 to +85
Pin 26(Note 1) (Note 5)
Pin 22(Note 1) (Note 5)
Pin Voltage 3
VPIN3
V
Pin 19(Note 1) (Note 5)
Pin 15(Note 1) (Note 5)
Pin 7(Note 1)
Pin Voltage 4
VPIN4
VERR
Topr
Tstg
Tj
V
V
°C
°C
°C
Open-drain Pin Voltage
Operating Temperature Range
Storage Temperature Range
Junction Temperature Range
Pin 13(Note 1)
-55 to +150
-40 to +150
Caution 1: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is
operated over the absolute maximum ratings.
Caution 2: Should by any chance the maximum junction temperature rating be exceeded the rise in temperature of the chip may result in deterioration of the
properties of the chip. In case of exceeding this absolute maximum rating, design a PCB with thermal resistance taken into consideration by
increasing board size and copper area so as not to exceed the maximum junction temperature rating.
(Note 1) The voltage that can be applied reference to GND (Pin 8, 18, 23).
(Note 2) Do not exceed Tj=150°C.
(Note 3) Refer to Recommended Operating Ratings for VDVDD
.
(Note 4) This LSI should be used within AC peak limits at all conditions. Overshoot should be ≤30V with reference to GND.
Undershoot should be ≤10ns and ≤30V with reference to VCCP1 and VCCP2. (Refer to Figure 3-1)
(Note 5) This LSI should be used in lower than this rating by all means.
Undershoot should be ≤10ns and ≤ (VOUT1P or VOUT1N or VOUT2P or VOUT2N) +7V. (Refer to Figure 3-2)
Overshoot to OUT1P or
OUT1N or OUT2P or OUT2N
7V (Max)
VCCP1,
VCCP2
Overshoot to
GND
30V (Max)
Undershoot to Vcc
30V(Max)
BSP1P
BSP1N
BSP2P
BSP2N
Undershoot to OUT1P or
OUT1N or OUT2P or OUT2N
7V (Max)
OUT1P
OUT1N
OUT2P
OUT2N
GND
≦10ns
≦10ns
Figure 3-1
Figure 3-2
www.rohm.com
TSZ02201-0C1C0E900720-1-2
31.Aug.2018 Rev.001
© 2018 ROHM Co., Ltd. All rights reserved.
6/79
TSZ22111 • 15 • 001
ROHM [ ROHM ]
