欢迎访问ic37.com |
会员登录 免费注册
发布采购

RF2513 参数 Datasheet PDF下载

RF2513图片预览
型号: RF2513
PDF下载: 下载PDF文件 查看货源
内容描述: UHF发送器 [UHF TRANSMITTER]
分类和应用: 光电二极管
文件页数/大小: 14 页 / 323 K
品牌: RFMD [ RF MICRO DEVICES ]
 浏览型号RF2513的Datasheet PDF文件第1页浏览型号RF2513的Datasheet PDF文件第2页浏览型号RF2513的Datasheet PDF文件第4页浏览型号RF2513的Datasheet PDF文件第5页浏览型号RF2513的Datasheet PDF文件第6页浏览型号RF2513的Datasheet PDF文件第7页浏览型号RF2513的Datasheet PDF文件第8页浏览型号RF2513的Datasheet PDF文件第9页  
RF2513  
Pin  
1
Function Description  
Interface Schematic  
This pin is connected directly to the reference oscillator transistor base.  
OSC B2  
OSC B1  
OSC E  
OSC B2  
The intended reference oscillator configuration is a modified Colpitts.  
An appropriate capacitor as chosen by the customer should be con-  
nected between pin 1 and pin 2.  
This pin is connected directly to the emitter of the reference oscillator  
transistor. An appropriate capacitor as chosen by the customer should  
be connected from this pin to ground.  
See pin 1.  
2
3
OSC E  
This pin is connected directly to the reference oscillator transistor base. See pin 1.  
The intended reference oscillator configuration is a modified Colpitts.  
An appropriate capacitor as chosen by the customer should be con-  
nected between pin 3 and pin 2.  
OSC B1  
This pin is used to power up or down the VCO and PLL. A logic high  
(PLL ENABL>2.0V) powers up the VCO and PLL electronics. A logic  
4
PLL ENABL  
50 k  
PLL ENABL  
low (PLL ENABL<1.0V) powers down the PLL and VCO.  
Ground connection for the PA buffer amp. Keep traces physically short  
and connect immediately to ground plane for best performance.  
5
6
GND1  
VCC3  
This pin is used to supply DC bias to the transmitter PA. A RF bypass  
capacitor should be connected directly to this pin and returned to  
ground. A 100pF capacitor is recommended for 915MHz applications.  
A 220pF capacitor is recommended for 433MHz applications.  
This pin is used to vary the transmitter output power. An output level  
adjustment range greater than 12dB is provided through analog volt-  
age control of this pin. DC current of the transmitter power amp ia also  
reduced with output power. This pin MUST be low when the transmitter  
is disabled.  
7
LVL ADJ  
40 k  
LVL ADJ  
400  
4 kΩ  
RF output pin for the transmitter electronics. TX OUT output impedance  
is a low impedance when the transmitter is enabled. TX OUT is a high  
impedance when the transmitter is disabled.  
8
TX OUT  
VCC  
11  
20  
TX OUT  
Ground connection for the Tx PA functions. Keep traces physically  
short and connect immediately to ground plane for best performance.  
9
GND2  
VCC1  
This pin is used to supply DC bias to the PA buffer amp. A RF bypass  
capacitor should be connected directly to this pin and returned to  
ground. A 100pF capacitor is recommended for 915MHz applications.  
A 220pF capacitor is recommended for 433MHz applications.  
10  
Enables the transmitter circuits. TX ENABL>2.0V powers up all trans-  
mitter functions. TX ENABL<1.0V turns off all transmitter functions  
except the PLL functions.  
11  
TX ENABL  
20 k  
TX ENABL  
40 k  
Dual-modulus/Dual-divide prescaler output. The output can be inter-  
faced to an external PLL IC for additional flexibility in frequency pro-  
gramming.  
12  
13  
PRESCL  
OUT  
PRESCL  
OUT  
Bias voltage reference pin for bypassing the prescaler and phase  
detector. The bypass capacitor should be of appropriate size to provide  
filtering of the reference crystal frequency and be connected directly to  
this pin.  
VREF P  
Rev B8 010509  
11-25