欢迎访问ic37.com |
会员登录 免费注册
发布采购

RF2422 参数 Datasheet PDF下载

RF2422图片预览
型号: RF2422
PDF下载: 下载PDF文件 查看货源
内容描述: 2.5GHZ直接正交调制器 [2.5GHZ DIRECT QUADRATURE MODULATOR]
分类和应用:
文件页数/大小: 6 页 / 72 K
品牌: RFMD [ RF MICRO DEVICES ]
 浏览型号RF2422的Datasheet PDF文件第1页浏览型号RF2422的Datasheet PDF文件第2页浏览型号RF2422的Datasheet PDF文件第4页浏览型号RF2422的Datasheet PDF文件第5页浏览型号RF2422的Datasheet PDF文件第6页  
RF2422  
Pin  
1
Function Description  
Interface Schematic  
Reference voltage for the I mixer. This voltage should be the same as  
I REF  
Q REF  
GND2  
Q SIG  
Q REF  
the DC voltage supplied to the I SIG pin. A voltage of 3.0V is recom-  
mended. The SIG and REF inputs are inputs of a differential amplifier.  
Therefore the REF and SIG inputs are interchangeable. If swapping the  
I SIG and I REF pins, the Q SIG and Q REF also need to be swapped  
to maintain the correct phase. It is also possible to drive the SIG and  
REF inputs in a balanced mode. This will increase the gain.  
100Ω  
100Ω  
425Ω  
425Ω  
Reference voltage for the Q mixer. This voltage should be the same as  
the DC voltage supplied to the Q SIG pin. A voltage of 3.0V is recom-  
mended.  
2
3
Q SIG  
Q REF  
100Ω  
100Ω  
425Ω  
425Ω  
5
Ground connection of the LO phase shift network. This pin should be  
connected directly to the ground plane.  
Same as pin 3.  
Same as pin 3.  
4
5
6
GND2  
GND2  
LO  
The input of the phase shifting network. This pin has an internal DC-  
blocking capacitor. At frequencies higher than 2GHz this port is well-  
matched to 50. This port is voltage driven so matching at lower fre-  
quencies is not required.  
LO  
Power supply for all circuits except the RF output stage. An external  
capacitor is needed if no other low frequency bypass capacitor is  
nearby.  
7
8
VCC1  
PD  
Power Down control. When this pin is "low", all circuits are shut off. A  
"low" is typically 1.2V or less at room temperature.When this pin is  
VCC  
200 Ω  
"high" (V ), all circuits are operating normally. If PD is below V , out-  
CC  
CC  
PD  
put power and performance will be degraded. Operating in this region  
is not recommended, although it might be useful in some applications  
where power control is required.  
This is the 50RF Output. This pin has an internal DC-blocking capac-  
itor. At frequencies higher than 2GHz this port is well-matched. Typical  
impedances at lower frequencies are: 24-j30 @ 1GHz, 27-j10 @  
1.4GHz, 31-j3 @ 1.8GHz. At those frequencies, external matching  
may be needed to optimize output power.  
9
RF OUT  
RF OUT  
Ground connection for the RF output stage. This pin should be con-  
nected directly to the ground plane.  
10  
11  
12  
GND3  
VCC2  
GND1  
Power supply for the RF Output amplifier. An external capacitor is  
needed if no other low frequency bypass capacitor is near by.  
Ground connection for the LO and baseband amplifiers, and for the  
mixers. This pin should be connected directly to the ground plane.  
Same as pin 12.  
Same as pin 12.  
13  
14  
15  
GND1  
GND1  
Q SIG  
Baseband input to the Q mixer. This pin is DC-coupled. Maximum out- See pin 2.  
put power is obtained when the input signal has a peak to peak ampli-  
tude of 2V. The recommended DC level for this pin is 3.0V. The peak  
minimum voltage on this pin (V  
- peak modulation amplitude)  
REF  
should never drop below 2.0V. The peak maximum voltage on this pin  
(V + peak modulation amplitude) should never exceed 4.0V.  
REF  
Rev A5 010817  
5-31