欢迎访问ic37.com |
会员登录 免费注册
发布采购

FIREFLY-TX2 参数 Datasheet PDF下载

FIREFLY-TX2图片预览
型号: FIREFLY-TX2
PDF下载: 下载PDF文件 查看货源
内容描述: VIPER远程控制系统 [VIPER Remote Control Systems]
分类和应用: 远程控制
文件页数/大小: 6 页 / 1963 K
品牌: RFMD [ RF MICRO DEVICES ]
 浏览型号FIREFLY-TX2的Datasheet PDF文件第1页浏览型号FIREFLY-TX2的Datasheet PDF文件第2页浏览型号FIREFLY-TX2的Datasheet PDF文件第3页浏览型号FIREFLY-TX2的Datasheet PDF文件第4页浏览型号FIREFLY-TX2的Datasheet PDF文件第6页  
VIPER Remote Control Systems  
VIPER-S1M / VIPER S2M (230Vac Powered Receivers)  
Please Note: During Learn and Erase the relays operate at high speed. They should be isolated from sensi-  
tive equipment during this process.  
To Pair a Transmitter button to receiver Output Relay #1  
1.  
Apply power the receiver and wait 10secs for the unit to enter ‘normal operation’ mode.  
2.  
Switch the receiver unit OFF and then ON again in ~1sec intervals FOUR times finally leaving the unit  
powered.  
3.  
5.  
6.  
7.  
8.  
After 5 seconds the receiver emits a single ‘buzz’ The unit is now in ‘learn’ Mode  
Press the chosen transmitter button.  
The receiver will acknowledge by sounding the a single ’buzz’  
Press the same transmitter button again, to confirm OK. The receiver will “buz” again to confirm.  
Learn Process complete. After 10 seconds the unit will return to ‘normal operation’ mode.  
To Pair a Transmitter button to receiver Output Relay #2  
1.  
Apply power the receiver and wait 10secs for the unit to enter ‘normal operation’ mode.  
2.  
Switch the receiver unit OFF and then ON again in ~1sec intervals SIX times finally leaving the unit  
powered.  
3.  
5.  
6.  
7.  
After 5 seconds the receiver emits a double ‘buzz’ The unit is now in ‘learn’ Mode  
Press the chosen transmitter button.  
The receiver will acknowledge by sounding the a double ’buzz’  
Press the same transmitter button again, to confirm OK. The receiver will double “buzz” again to  
confirm.  
8.  
Learn Process complete. After 10 seconds the unit will return to ‘normal operation’ mode.  
Erasing Receivers Memory  
1.  
2.  
3.  
4.  
5.  
Power the receiver unit up and wait 10 seconds for the unit to enter ‘normal operation’ mode.  
Switch the unit off and then on again at ~1 second intervals TEN times, leaving the unit powered.  
Wait 5 seconds until a ‘clicking’ sound is heard for a period of 10 seconds.  
Wait 10 seconds for the receiver unit to return to ‘normal’ mode  
The unit has now erased all encoder data.  
NOTE: You cannot erase individual Tx encoders  
Configuring Receiver Outputs  
The jumper links configure the outputs to be Momentary or Latching.  
The jumper links are made/removed by the small link ‘cap’ placed  
over the pin header.  
Link Positions - Relay Outputs  
LK1  
Open  
Relay #1  
Mom  
LK2  
Open  
Relay #2  
Mom  
Closed  
Latch  
Closed  
Latch  
(the above image shows, RLY2 Momentary, RLY1 Latched)  
DS VIPER-2  
©2009 REG No 277 4001, Lewes, England. Page 5