欢迎访问ic37.com |
会员登录 免费注册
发布采购

R1LP0408CSP-7LC 参数 Datasheet PDF下载

R1LP0408CSP-7LC图片预览
型号: R1LP0408CSP-7LC
PDF下载: 下载PDF文件 查看货源
内容描述: 4M SRAM( 512千字】 8位)的 [4M SRAM (512-kword 】 8-bit)]
分类和应用: 静态存储器
文件页数/大小: 14 页 / 93 K
品牌: RENESAS [ RENESAS TECHNOLOGY CORP ]
 浏览型号R1LP0408CSP-7LC的Datasheet PDF文件第4页浏览型号R1LP0408CSP-7LC的Datasheet PDF文件第5页浏览型号R1LP0408CSP-7LC的Datasheet PDF文件第6页浏览型号R1LP0408CSP-7LC的Datasheet PDF文件第7页浏览型号R1LP0408CSP-7LC的Datasheet PDF文件第9页浏览型号R1LP0408CSP-7LC的Datasheet PDF文件第10页浏览型号R1LP0408CSP-7LC的Datasheet PDF文件第11页浏览型号R1LP0408CSP-7LC的Datasheet PDF文件第12页  
R1LP0408C-C Series
Write Cycle
R1LP0408C-C
-5SC
Parameter
Write cycle time
Chip selection to end of write
Address setup time
Address valid to end of write
Write pulse width
Write recovery time
Write to output in high-Z
Data to write time overlap
Data hold from write time
Output active from end of write
Output disable to output in high-Z
Symbol
t
WC
t
CW
t
AS
t
AW
t
WP
t
WR
t
WHZ
t
DW
t
DH
t
OW
t
OHZ
Min
55
50
0
50
40
0
0
25
0
5
0
Max
20
20
-7LC
Min
70
60
0
60
50
0
0
30
0
5
0
Max
25
25
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
2
1, 2, 7
3, 12
6
1, 2, 7
4
5
Notes
Notes: 1. t
HZ
, t
OHZ
and t
WHZ
are defined as the time at which the outputs achieve the open circuit conditions
and are not referred to output voltage levels.
2. This parameter is sampled and not 100% tested.
3. A write occurs during the overlap (t
WP
) of a low CS# and a low WE#. A write begins at the later
transition of CS# going low or WE# going low. A write ends at the earlier transition of CS# going
high or WE# going high. t
WP
is measured from the beginning of write to the end of write.
4. t
CW
is measured from CS# going low to the end of write.
5. t
AS
is measured from the address valid to the beginning of write.
6. t
WR
is measured from the earlier of WE# or CS# going high to the end of write cycle.
7. During this period, I/O pins are in the output state so that the input signals of the opposite phase
to the outputs must not be applied.
8. If the CS# low transition occurs simultaneously with the WE# low transition or after the WE#
transition, the output remain in a high impedance state.
9. Dout is the same phase of the write data of this write cycle.
10. Dout is the read data of next address.
11. If CS# is low during this period, I/O pins are in the output state. Therefore, the input signals of
the opposite phase to the outputs must not be applied to them.
12. In the write cycle with OE# low fixed, t
WP
must satisfy the following equation to avoid a problem of
data bus contention. t
WP
t
DW
min + t
WHZ
max
Rev.2.00, May.26.2004, page 8 of 12