欢迎访问ic37.com |
会员登录 免费注册
发布采购

M37221EASP 参数 Datasheet PDF下载

M37221EASP图片预览
型号: M37221EASP
PDF下载: 下载PDF文件 查看货源
内容描述: 单片8位微机的CMOS电压合成器与屏幕上的显示控制器 [SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER]
分类和应用: 显示控制器计算机
文件页数/大小: 112 页 / 1165 K
品牌: RENESAS [ RENESAS TECHNOLOGY CORP ]
 浏览型号M37221EASP的Datasheet PDF文件第64页浏览型号M37221EASP的Datasheet PDF文件第65页浏览型号M37221EASP的Datasheet PDF文件第66页浏览型号M37221EASP的Datasheet PDF文件第67页浏览型号M37221EASP的Datasheet PDF文件第69页浏览型号M37221EASP的Datasheet PDF文件第70页浏览型号M37221EASP的Datasheet PDF文件第71页浏览型号M37221EASP的Datasheet PDF文件第72页  
M37221M4H/M6H/M8H/MAH–XXXSP/FP M37221EASP/FP  
8.11.5 Color Register  
The color of a displayed character can be specified by setting the  
color to one of the 4 registers (CO0 to CO3: addresses 00E616 to  
00E916) and then specifying that color register with the OSD RAM.  
There are 3 color outputs; R, G and B. By using a combination of  
these outputs, it is possible to set 8 colors. However, since only 4  
color registers are available, up to 4 colors can be disabled at one  
time.  
R, G and B outputs are set by using bits 1 to 3 in the color register. Bit  
5 is used to specify whether a character output or blank output. Bits  
4, 6 and 7 are used to specify character background color. Figure  
8.11.12 shows the color register.  
Color Register i  
b7 b6 b5 b4 b3 b2 b1 b0  
Color register i (COi) (i = 0 to 3) [Addresses 00E616 to 00E916]  
B
0
Name  
Functions  
After reset  
0
R
W
Nothing is assigned. This bit is a write disable bit.  
When this bit is read out, the value is “0.”  
R —  
1
2
3
4
5
6
7
W
W
W
W
W
W
W
B signal output selection  
bit (COi1)  
0: No character is output  
1: Character is output  
0
0
0
0
0
0
0
R
R
R
R
R
R
R
G signal output selection  
bit (COi2)  
0: No character is output  
1: Character is output  
0: No character is output  
1: Character is output  
R signal output selection  
bit (COi3)  
B signal output (background)  
selection bit (COi4) (See note 1)  
0: No background color is output  
1: Background color is output  
0: Character is output  
1: Blank is output  
OUT1 signal output control bit  
(COi5) (See notes 1, 2)  
0: No background color is output  
1: Background color is output  
G signal output (background)  
selection bit (COi6) (See note 1)  
R signal output (background)  
0: No background color is output  
selection bit (COi7) (See note 2) 1: Background color is output  
Notes 1: When bit 5 =“0” and bit 4 = “1,” there is output same as a character or  
border output from pin OUT1.  
Do not set bit 5 = “0” and bit 4 = “0.”  
2: When only bit 7 =“1” and bit 5 “0,” there is output from pin OUT2.  
Fig. 8.11.13 Color Register i  
Rev.1.00 Oct 01, 2002 page 68 of 110  
REJ03B0134-0100Z  
 复制成功!