DG508A
Absolute Maximum Ratings
Thermal Information
o
o
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V
V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
Thermal Resistance (Typical, Note 2)
θ
( C/W)
θ
( C/W)
JA
JC
16 Ld CERDIP Package. . . . . . . . . . . .
16 Ld PDIP Package . . . . . . . . . . . . . .
Maximum Junction Temperature
75
90
20
N/A
Digital Inputs, V , V (Note 1). . . . . . . . . . . . . .(V- -2V) To (V+ +2V)
S
D
Continuous Current, (Any Terminal Except S or D) . . . . . . . . . 30mA
Continuous Current, (S or D) . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . . . . 40mA
o
CERDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 C
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 C
o
Maximum Storage Temperature
“A” and “B” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . -65 C to 150 C
“C” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 C to 125 C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300 C
o
o
Operating Conditions
o
o
Temperature Range
“A” Suffix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55 C to 125 C
“B” Suffix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25 C to 85 C
“C” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 C to 70 C
o
o
o
o
o
o
o
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on S , D, E , or A exceeding V+ or V- are clamped by internal diodes. Limit diode current to maximum current ratings.
X
N
X
2. θ is measured with the component mounted on an evaluation PC board in free air.
JA
o
Electrical Specifications T = 25 C, V+ = +15V, V- = -15V, GND = 0V, V = 2.4V, Unless Otherwise Specified
A
EN
“A” SUFFIX
“B” AND “C” SUFFIX
(NOTE 4) (NOTE 3) (NOTE 4) (NOTE 4) (NOTE 3) (NOTE 4)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
MIN
TYP
MAX
UNITS
DYNAMIC CHARACTERISTICS
Switching Time of
Multiplexer, t
See Figure 1
See Figure 3
See Figure 2
See Figure 2
-
-
-
-
-
0.6
0.2
1
1
-
-
-
-
-
-
0.6
0.2
1
-
-
-
-
-
µs
µs
µs
µs
dB
TRANSITION
Break-Before-Make
Interval, t
OPEN
Enable Turn-ON Time,
1.5
1.0
-
t
ON(EN)
Enable Turn-OFF Time,
0.4
68
0.4
68
t
OFF(EN)
OFF Isolation, OIRR
V
= 0V, R = 1kΩ, C = 15pF,
EN L L
V
= 7V
, f = 500kHz (Note 5)
S
RMS
Source OFF Capacitance,
V
V
= 0V, V
= 0V, f = 140kHz
= 0V, f = 140kHz
-
-
-
5
25
4
-
-
-
-
-
-
5
25
4
-
-
-
pF
pF
pC
S
EN
EN
C
S(OFF)
Drain OFF Capacitance,
= 0V, V
D
C
D(OFF)
Charge Injection, Q
See Figure 4
DIGITAL INPUT CHARACTERISTICS
Address Input Current,
Input Voltage High, I
V
= 2.4V
= 15V
-10
-
-0.002
0.006
-
10
-
-10
-
-0.002
0.006
-
10
-
µA
µA
µA
µA
A
AH
V
A
AddressInputCurrentInput
V
= 2.4V
= 0V
V
= 0V
-10
-10
-0.002
-0.002
-10
-10
-0.002
-0.0002
EN
EN
A
Voltage Low, I
AL
V
-
-
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range,
(Note 7)
-15
-
+15
-15
-
+15
V
V
ANALOG
Drain-Source ON
Resistance, r
SequenceEach
Switch ON
I
I
= -200µA, V = +10V
-
-
270
230
400
400
-
-
270
230
450
450
Ω
Ω
S
S
D
DS(ON)
= -200µA, V = -10V
D
V
= 0.8V,
= 2.4V
AL
V
AH
r
Matching
-10V ≤ V ≤ +10V
-
6
-
-
6
-
%
DS(ON)
Between Channels
S
r
– r
DS(ON)MAX
DS(ON)MIN
∆r
= -----------------------------------------------------------------------
DS(ON)
r
DS(ON)AVG
3
RENESAS [ RENESAS TECHNOLOGY CORP ]
