欢迎访问ic37.com |
会员登录 免费注册
发布采购

TNY377P 参数 Datasheet PDF下载

TNY377P图片预览
型号: TNY377P
PDF下载: 下载PDF文件 查看货源
内容描述: 高能效,离线式开关采用增强的峰值功率性能 [Energy-Efficient, Off-Line Switcher With Enhanced Peak Power Performance]
分类和应用: 开关光电二极管
文件页数/大小: 22 页 / 1686 K
品牌: POWERINT [ Power Integrations ]
 浏览型号TNY377P的Datasheet PDF文件第5页浏览型号TNY377P的Datasheet PDF文件第6页浏览型号TNY377P的Datasheet PDF文件第7页浏览型号TNY377P的Datasheet PDF文件第8页浏览型号TNY377P的Datasheet PDF文件第10页浏览型号TNY377P的Datasheet PDF文件第11页浏览型号TNY377P的Datasheet PDF文件第12页浏览型号TNY377P的Datasheet PDF文件第13页  
TNY375-380  
Peak Output Power Table  
Key Application considerations  
230 VAC 1ꢀ5  
8ꢀ-26ꢀ VAC  
TinySwitch-PK Design Considerations  
Product  
ILIMIT-  
ILIMIT-  
ILIMIT-  
PEAKred  
ILIMIT-  
PEAKinc  
ILIMITPEAK  
ILIMITPEAK  
Output Power Table  
PEAKred  
PEAKinc  
Data sheet maximum output power table (Table 1) represents  
the maximum practical continuous output power level that can  
be obtained under the following assumed conditions:  
TNY375P/G/D  
TNY376P/G/D  
TNY377P/G  
TNY378P/G  
TNY379P/G  
TNY380P/G  
8.ꢀ W 14.ꢀ W 16.ꢀ W ꢀ.ꢀ W 11.ꢀ W 12.ꢀ W  
10 W  
13 W  
19 W  
23 W  
22 W  
28 W  
6 W  
8 W  
1ꢀ W  
18 W  
17 W  
23 W  
16 W 27.ꢀ W 34 W  
18 W 31.ꢀ W 39 W  
10 W 21.ꢀ W 27 W  
1. The minimum DC input voltage is 100 V or higher for 8ꢀ VAC  
input, or 220 V or higher for 230 VAC input or 11ꢀ VAC with  
a voltage doubler. The value of the input capacitance should  
be sized to meet these criteria for AC input designs.  
2. Efficiency of 7ꢀ5.  
12 W  
14 W  
2ꢀ W  
28 W  
31 W  
3ꢀ W  
20 W  
36 W  
4ꢀ W  
Table 2.  
Peak Output Power Capability vs Current Limit Mode Selection.  
3. Minimum data sheet value of I2f.  
The values shown in Table 1 for peak power assume operation  
in ILIMITPEAKinc. For reference, Table 2 provides peak output  
powers for each family member at all three selectable current  
limit modes.  
4. Transformer primary inductance tolerance of 105.  
ꢀ. Reflected output voltage (VOR) of 13ꢀ V.  
6. Voltage only output of 12 V with an ultrafast PN rectifier diode.  
7. Continuous conduction mode operation with transient KP*  
value of 0.2ꢀ.  
For both Table 1 and Table 2, the peak output power values are  
limited electronically, based on minimum device I2f. Stated  
differently, with sufficient heat sinking, these values could be  
delivered indefinitely, but in most cases this would be  
impractical. Adapter and open frame power values are  
thermally limited and represent the practical continuous (or  
average) output power in two common thermal environments.  
8. Increased current limit is selected for peak and open frame  
power columns and standard current limit for adapter  
columns.  
9. The part is board mounted with SOURCE pins soldered to  
sufficient area of copper and/or a heat sink is used to keep  
the SOURCE pin temperature at or below 110 °C for P and  
G package and 100 °C for D packaged devices.  
10. Ambient temperature of ꢀ0 °C for open frame designs and  
40 °C for sealed adapters.  
Over Voltage Protection  
The output overvoltage protection provided by TinySwitch-PK  
uses an internal latch that is triggered by a threshold current of  
approximately 7 mA into the BYPASS pin. In addition to an  
internal filter, the BYPASS pin capacitor forms an external filter,  
providing noise immunity from inadvertent triggering. For the  
bypass capacitor to be effective as a high frequency filter, it  
*KP. Below a value of 1, KP is the ratio of ripple to peak primary  
current. A transient KP limit of ≥0.2ꢀ is recommended to avoid  
premature termination of switching cycles due to initial current  
limit (IINIT) being exceeded, which reduces maximum output  
power capability.  
C9  
2.2 nF  
250 VAC  
C4  
1000 µF  
16 V  
C5  
220 µF  
16 V  
C3  
1000 µF  
16 V  
D5  
SB560  
T1  
EFD25  
+12 V  
RTN  
1
3
9,10  
D1  
L2  
3.3 µH  
1N4007  
VR3  
P6KE170A  
C8  
D2  
F1  
3.15 A  
10 nF  
1 kV  
1N4007  
L
C2  
6,7,8  
22 µF  
400 V  
C1  
10 µF  
400 V  
R7  
22 Ω  
1/2 W  
185 - 265  
VAC  
R9  
3.9 MΩ  
R4  
20 Ω  
R1  
1 kΩ  
N
VR1  
BZX55B11  
11 V, 2%  
5
2
D3  
1N4007  
D4  
1N4007  
D6  
UF4004  
D7  
R10  
3.9 MΩ  
UF4007  
L1  
1 mH  
C7  
VR2  
1N5251B, 22 V  
1 µF  
50 V  
R2  
390 Ω  
1/8 W  
R5  
47 Ω  
R6  
U2  
1/8 W  
21 kΩ  
D
S
PC817A  
1%  
EN/UV  
BP  
TinySwitch-PK  
U1  
R3  
2 kΩ  
1/8 W  
TNY380P  
C6  
10 µF  
50 V  
PI-4674-012009  
Figure 15. Single 230 VAC Input 20 W Continuous and 45 W Peak Power Supply Using TNY380PN.  
9
www.powerint.com  
Rev. C 09/12